Ergonomic Evaluation of Vibrations of a Rototiller with New Blade

ماشین های کشاورزی

Article 14, Volume 7, Issue 2 - Serial Number 14, 2017, Pages 491-502   

Document Type: Research Article

DOI: 10.22067/jam.v7i2.56061

Authors

H. Gholami¹; D. Kalantari^{* 1}; M. Rajabi Vandechali²

¹Department of Biosystems Engineering, Sari Agricultural Sciences and Natural Resources University (SANRU), Sari, Iran

²Department of Mechanic, Islamic Azad University of Jouybar, Jouybar, Mazandaran, Iran

Abstract

Introduction
One of the most important problems arising with operation of the conventional rototillers is severe vibration of the machine handle which is transmitted to the user’s hands, arms and shoulders. Long period exposure of the hand-transmitted vibration may cause various diseases such as white finger syndrome. Therefore in this study, vibrations of a new type of rototiller with ridged blades were investigated at the position of handle/hand interface in different working conditions. Finally, the maximum allowable exposure time to the rototiller users in continuous tillage operation was obtained according to ISO 5349-1.
Materials and Methods
Experiments were carried out in one of the farms with silty clay soil texture, located in Sari city, Mazandaran province, Iran. Vibration measurements were performed according to ISO 5349-1 and ISO 5349-2 standards in two different modes, including in situ mode and tillage mode. Vibrational parameters were obtained in three blade rotational speeds, i.e., low speed (140-170 rpm), medium speed (170-200), and high speed (200-230). Blade rotational speed varied by changing engine speed using the throttle control lever. In each experiment, different vibrational values were individually recorded in three directions (x, y, and z). Experimental design and data analysis were performed in a Randomized Complete Block Design with three replications using the SPSS16 software.
Results and Discussion
Based on the obtained results in this study, the RMS of acceleration increased by increasing in rotational speed for all of the conducted experiments. The reason is that number of cutting per unit of time and consequently the frequency of changing in the dynamic forces exerting on the blades dramatically increases with increasing the rotational speed of the blades. Noteworthy is that in most cases the variation of acceleration in the tillage mode showed similar trend with vibrational values in the idling mode. This represents a significant contribution of the combustion engine in vibration of the examined rototiller. Meanwhile, contribution of the engine in the total measured vibration was more than 50% at different rotational speeds and different directions. The minimum engine contribution was measured equal to 56.39% in z-direction at 155 rpm, whereas the maximum engine contribution was observed equal to 79.5%, in x-direction and rotational speed of 215 rpm. These results indicate the importance of selecting a proper combustion engine for reducing the rototiller vibration. It should be noted that the contribution of the engine in total vibration reached its minimum value at the speed related to the maximum generated torque, i.e., 185 rpm of the rotor speed.
This result indicates that using the combustion engine in its optimum speed reduces the entire device vibration in the vertical direction. By increasing the rotational speed of the blades in the y-direction, engine contribution in device vibration showed different trends in compare to the other directions. The most value was equal to 74.25% which was obtained at the rotation speed of 185 rpm. By increasing blade rotational speed from 155 rpm to 215 rpm, the engine contribution in device vibration in the z direction and the total acceleration steadily increased.
Conclusion
With growing mechanization and entering various types of machines to the farm, importance of considerations to human health is also increased, especially in working with rotational machines. Therefore, the current study was undertaken with the specific attention to the rototillers operational vibration at the handle/hand interface. Results of the conducted experiments showed that vibration of the examined rototiller depends more on the operation of the mounted combustion engine, rather than the soil working blades. Therefore, it is suggested to select a higher quality engine with less vibration or isolate the engine from chassis by a damper (such as a compressed rubber) to reduce the vibration transmitted to the operator’s hands and arms.

Keywords

Allowable exposure time; Ergonomy; Hand and arm; Rototiller; Vibration

References

1. American Conference of Governmental Industrial Hygienists (ACGIH). 2002.

2. Bernaki H., J. Haman, and C. Z. Kanafojski. 1972. Agricultural machines, theory and construction.US department of Agriculture and national science foundation, Washington, D.C.

3. Boshuizen, H. C., P. M. Bongers, and C. T. J. Hulshof. 1990. Self-reported back pain in tractor drivers exposed to whole-body vibration. International Archives of Occupational and Environmental Health 62: 109-115.

4. Chaturvedi, V., A. Kumar, and J. K. Singh. 2012. Power tiller: Vibration magnitudes and intervention development for vibration reduction. Applied Ergonomics 43: 891-901.

5. Dewangan, K. N., and V. K. Tewari. 2009. Characteristics of hand-transmitted vibration of a hand tractor used in three operational modes. International Journal of Industrial Ergonomics 39: 239-245.

6. Donati, P. 2008. Workplace exposure to vibration in Europe: an expert review Vol. 7.

7. Fayzi, M., A. Jafari, and H. Ahmadi. 2014. Investigation and analysis the vibration of handles of chainsaw without cutting. Journal of Agricultural Machinery 6 (1): 90-101. (In Farsi).

8. Gholami, H., D. Kalantari, and M. Rajabi vandechali. 2016. Testing and evaluation of a rototiller with new ridged blades. Journal of Agricultural Machinery 7 (1). (In Farsi).

9. Goglia, V., Z. Gospodaric, D. Filipovic, and I. Djukic. 2006. Influence on operator’s health of hand-transmitted vibrations from handles of a single-axle tractor. Annals of Agricultural and Environmental Medicine 13: 33-38.

10. Griffin, M. 2004. Minimum health and safety requirements for workers exposed to hand-transmitted vibration and whole-body vibration in the European Union; a review. Occupational and Environmental Medicine 61 (5): 387-397.

11. Hashemifard Dehkordi, S. H., M. Almassi, A. M. Borgheei, and B. Beheshti. 2013. Effect of bio ethanol and diesel blend on small diesel engine vibration. Journal of Agricultural Machinery 4 (2): 236-243. (In Farsi).

12. ISO 5349-1. 2001. Mechanical Vibration Measurement and Evaluation of Human Exposure to Hand-transmitted Vibration. Part I: General Requirements. Geneva: International Standard Organization.

13. ISO 5349-2. 2001. Mechanical Vibration-Measurement and Evaluation of Human Exposure to Hand-Transmitted Vibration-Part 2: Practical Guidance for Measurement at the Workplace.

14. Issever, H., C. Aksoy, H. Sabuncu, and A. Karan. 2003. Vibration and its effects on the body. Medical Principles and Practice 12: 34-38.

15. Marsili, A., L. Ragni, G. Santoro, P. Servadio, and G. Vassalini. 2002. Innovative systems to reduce vibrations on agricultural tractors: Comparative analysis of acceleration transmitted through the driving seat. Biosystem Engineering 81: 35-47

16. Nassiri, P., I. Ali Mohammadi, M. H. Beheshti, and K. Azam. 2013. Hand-Arm vibration assessment among tiller operator. Journal of health and safety at work. 3 (2): 35-46. (In Farsi).

17. Rao, S. S. 2011. Mechanical Vibrations. Prentice Hall. P 1084.

18. Salokhe, V. M., B. Majumder, and M. S. Islam. 1995. Vibration characteristics of a power tiller. Journal of Terramechanics 32: 181-197.

19. Sam B., and K. Kathirvel. 2006. Vibration Characteristics of Walking and Riding Type Power Tillers. Biosystem Engineering 95: 517-528.

20. Tabatabae Koloor, R., and Gh. Kiani. 2011. Investigation of the rototiller blades operational factors on the orchards and paddy fields tillage. Journal of Agricultural Machinery Engineering 1 (1): 34-40. (In Farsi).

21. Taghizadeh Ali sarai, A., T. Tavakoli Hashjin, and B. Ghobadian. 2010. Tiller vibration analysis at station position. Iran Biosystems Engineering 41: 27-35. (In Farsi).

22. Tewari, V. K., K. N. Dewangan, and S. Karmakar. 2004. Operator’s fatigue in field operation of hand tractors. Biosystems Engineering 89: 1-11.

23. Tewari, V. K., and K. N. Dewangan. 2009. Effect of vibration isolators in reduction of work stress during field operation of hand tractor. Biosystems Engineering 103 (2): 146-158.