Study of The Vapor Thermo-Compressor to Reduce Energy Consumption in the Sugar Production Line using Computational Fluid Dynamics

ماشین های کشاورزی

Article 10, Volume 10, Issue 2 - Serial Number 20, 2020, Pages 241-253   

Document Type: Research Article

DOI: 10.22067/jam.v10i2.76872

Authors

A. Rezvanivand fanaei; A. Hasanpour^* ; A. M. Nikbakht

Biosystems Engineering Department, Faculty of Agriculture, Urmia University, Urmia, Iran

Abstract

Introduction
Large industrial factories often discharge significant quantities of low-pressure steam (dead steam) into the atmosphere, which causes energy losses. Retaining low-pressure steam content reduces boiler load, resulting in energy savings and lower costs for the fuel consumption (for example, gas consumption bill in a factory). The boosted-pressure steam is used in processes such as distillation, hot water production, space heating or vacuum generation. If the vapor pressure for the intended application is low, a thermo-compressor is able to increase the pressure and temperature to the required level. Thermo-compressors are a special type of gas compressor that uses an actuator to compress secondary fluid and does not have any blades or moving parts. The accurate prediction of the thermo-compressor performance improves the reliability of this process and increases its efficiency.
Materials and Methods
Two important characteristics for the current thermo-compressors are entrainment ratio (ER) and compression ratio (CR). The first is the dimensionless mass flow rate, and the second is the dimensionless pressure. The wet steam theory as a classic theory is used by Wolmer-Frankel-Zeldovich to calculate the amount of liquid particles. In order to select the best geometry for the thermo-compressor among all possible geometries, the performance of each model must be compared with other models. In following, the case that includes characteristic parameters associated with the target values has been selected.
The commercial Ansys Fluent Versions 15, based on the finite volume method (FVM) was used to simulate and monitoring the flow behavior inside the thermo-compressor. The governing partial differential equations (PDE) were solved implicitly using a density-based solution. The convective heat transfer terms were discriminated based on the second-order upwind scheme. The non-linear governing equations were solved using the implicit coupling solver and the standard wall function was used near the wall. Given the three-dimensional flow for steam, the equations of mass conservation, momentum, and energy were written. The Realizable  model was used to simulate turbulences in the flow.
Results and Discussion
A summary of the results is presented in terms of the results of pressure, velocity magnitude, Mach number and temperature. A general understanding of this characteristic for a thermo-compressor is extremely important for recognizing the fluid flow inside it, and it is very useful for practical use. Pressure is the most important factor in the recharge section of a thermo-compressor. Increasing the recharge vapor pressure in a thermos-compressor revival the dead steam and increases the steam efficiency. The revival steam can be used in other parts because of their high thermal content. Another important factor in the study of flow behavior inside the thermocouple is velocity magnitude. This quantity, which is closely related to the concept of momentum inside the thermocouple, had high influences from high pressure inputs as well as the thermo-compressor geometry. The highest amount of velocity occurs after the initial nozzle and had a very high magnitude (1000 ms^-1), which was also remarkably high in Monnet's terms. Another important characteristic of a flow is the temperature of the stream. The high input temperature associated with motive vapor at the outlet of the primary nozzle was sharply reduced, even in some section reached to 110 °Kelvin. Due to the very high flow momentum in this section, the fluid phase remained gas and it can be justified from the point of view of the fluid dynamics.
Conclusion
Considering the importance of thermodynamic properties of steam in conversion and industries, it would be extremely beneficial to fully understand the interactions inside the thermocouple compressor. The importance of the discussed characteristics is more specific when there is a close relationship between each of these factors and energy consumption in a factory or in any industrial production unit. It was observed that the designed thermos-compressor was able to increase the velocity and temperature in a desirable range for the conversion of non-consumable vapor to the pressure and temperature. It was concluded that the Realizable  model due to the prediction of the jet characteristics appearing in the flow regimes for axial symmetry had a high ability to simulate fluid flows inside the thermos-compressor.

Keywords

Thermo-compressor; computational fluid dynamics; Control volume method; Consumption energy

References

1. Chen, F., C. F. Liu, and J. Y. Yang. 1994. Supersonic flow in the second-throat ejector–diffuser system. Journal of Spacecraft and Rockets 31 (1): 123-129.

2. Fan, J., J. Eves, H. M. Thompson, V. V. Toropov, N. Kapur, and D. Copley. 2011. Computational fluid dynamic analysis and design optimization of jet pumps. Computers & Fluids 46: 212- 217.

3. Giacomelli, F., G. Biferi, F. Mazzelli, and A. Milazzo. 2016. CFD Modeling of the Supersonic Condensation inside a Steam Ejector. Energy Procedia 101: 1224-1231.

4. Gyarmathy, G. 1963. On the growth rate of droplets in a supersaturated atmosphere. Zeitschrift für angewandte Mathematik und Physik 14 (13): 280-293.

5. Gyarmathy, G. 1976 .Condensation in flowing steam, a von-Karman institute book on two-phase steam flow in turbines and separators. Hemisphere 127-89.

6. Han, B., Z. Liu, H. Wu, and Y. Li. 2014. Experimental study on a new method for improving the performance of thermal vapor compressors for multi-effect distillation systems. Desalination 344: 391-3955.

7. Kantrowitz, A. 1951. Nucleation in very rapid vapor expansions. The Journal of Chemical Physics 19:1097-1100.

8. Khalid, K. A., M. A. Antar, A. Khalifa, O. A. Hamed. 2018. Allocation of thermal vapor compressor in multi effect desalination systems with different feed configurations. Desalination 426: 164-173.

9. Kim, S. D., I. S. Jeong, and D. J. Song. 2007. A computational analysis of unsteady transonic/ supersonic flows over backward facing step in air jet nozzle. Journal of Mechanical Science and Technology 21 (2): 336-348.

10. McDonald, J. E. 1962. Homogeneous nucleation of water vapor condensation: I. Thermodynamic aspects. American Journal of Physics 30: 870-877.

11. MyoungKuk, J., T. Utomo, J. Woo, Y. H. Lee, H. M. Jeong, and H. S. Chung. 2010. CFD investigation on the flow structure inside thermo vapor compressor. Energy 35: 2694-2702.

12. Naddi, F., S. A. Mehdizadeh, and U. N. Zonuz. 2017. Comparing between predicted output temperature of flat-plate solar collector and experimental results: computational fluid dynamics and artificial neural network. Journal of Agricultural Machinery 7 (1): 298-311. (In Farsi).

13. Pianthong, K., W. Seehanam, M. Behnia, T. Sriveerakul, and S. Aphornratana. 2007. Investigation and improvement of ejector refrigeration system using computational fluid dynamics technique. Energy Conversion and Management 48: 2556-2564.

14. Rezvanivandefanayi, A., and A. M. Nikbakht. 2015. A CFD Study of the Effects of Feed Diameter on the Pressure Drop in Acyclone Separator. International Journal of Food Engineering 11: 71-77.

15. Riffat, S. B., G. Gan, and S. Smith. 1996. Computational fluid dynamics applied to ejector heat pumps. Applied Thermal Engineering 16: 291-297.

16. Rusly, E., and L. Aye. 2005. CFD analysis of ejector in a combined ejector cooling system. International Journal of Refrigeration 28: 1092-1100.

17. Shari, N., M. Boroomand, and R. Kouhikamali. 2012. Wet steam flow energy analysis within thermo-compressors. Energy 47: 609-619.

18. Sharifi, N., and M. Boroomand. 2013. An investigation of thermo-compressor design by analysis and experiment. Part 2. Development of design method by using comprehensive characteristic curves. Energy Conversion and Management 69: 228-237.

19. Simpson, D. A., and A. J. White. 2005. Viscous and unsteady flow calculations of condensing steam in nozzles. International Journal of Heat and Fluid Flow 26: 71-79

20. Young, J. B. 1982. The spontaneous condensation of steam in supersonic nozzles. Physicochemical Hydrodynamics 3 (1): 57-82.

21. Young, J. B. 1992. Two-dimensional non-equilibrium wet-steam calculations for nozzles and turbine cascades. Journal of Turbomachinery 114: 569-578.