Investigation of microstructure and mechanical properties of dissimilar joints between AISI 321 stainless steel and X65 high-strength low-alloy steel

مهندسی متالورژی و مواد

Article 5, Volume 33, Issue 1 - Serial Number 25, May 2021, Pages 71-86   

Document Type: Original Article

DOI: 10.22067/jmme.2021.71525.1020

Authors

Mahmood Sharifitabar^{* 1}; Sahar Khajeh Mahmoodi²

¹Department of Materials Engineering, University of Sistan and Baluchestan, Zahedan .

²M.Sc./ University of Sistan and Baluchestan

Abstract

In the present study, a dissimilar joint was established between 321 stainless steel and X65 high-strength low-alloy steel by shielded metal arc welding process using 308 and 309 stainless steel electrodes as filler materials. Then, the structure, microstructure, hardness, and tensile properties of the joints were investigated. Results showed that austenite and delta ferrite phases developed in the structure of the joints. Microstructure characterization confirmed that the volume fraction of delta ferrite in the microstructure of 309 weld metal was higher than the 308 electrode weld metal. A ferritic+martensitic layer was formed at the interface of both weld metals and X65 steel. The hardness of 308 and 309 weld metals was 30% and 38% higher than the low alloy steel base metal, respectively. Tensile test results showed that the strength of the joint set up using 309 electrode was 1.5% higher and its elongation was 26% lower than the joint made by 308 electrode. In all specimens fractured occurred at the interface between the weld metal and the low alloy steel. A mixed ductile-brittle fracture mode was observed on the fracture surface of tensile test specimens.

Keywords

Stainless steel; High-strength low-alloy steel; dissimilar joint; Strength; Hardness; Microstructure

References

1. ناظم الرعایا، علیرضا، و فاضل نجف‌آبادی، محمود، "بررسی ریزساختار و خواص مکانیکی اتصال فولاد API-X65 به‌روش جوش‌کاری هم‌زن اصطکاکی"، فرآیندهای نوین در مهندسی مواد، شماره 9، صفحه 75-84، (2017).
2. حیدری، معصومه، "اثر حرارت ورودی بر خواص مکانیکی و شکست جوش GMAW فولاد خط لوله در حضور هیدروژن"، پایان‌نامۀ کارشناسی ارشد مهندسی مواد، دانشکده مهندسی مواد، دانشگاه تربیت مدرس، (1395).
3. Sayyar, N., Shamanian, M. and Niroumand, B., "Arc Weldability of Incoloy 825 to AISI 321 Stainless Steel Welds", Journal of Materials Processing Technology, 262, pp. 562-570, (2018).
4. Kumar, P. and Sinha, A.N., "Effect of Pulse Width in Pulsed Nd:YAG Dissimilar Laser Welding of Austenitic Stainless Steel (304 L) and Carbon Steel (st37)", Lasers in Manufacturing and Materials Processing, 5, pp. 317-334, (2018).
5. Poorkabirian, M., Mostaan, H. and Rafiei, M., "The Effect of Filler Metal on Properties of AISI 4130 to AISI 316L Dissimilar Joint", Journal of Advanced Materials In Engineering, 36, pp. 33-46, (2017).
6. Pouraliakbar, H., Hamedi, M., Kokabi, A.H. and Nazari, A., "Designing of CK45 Carbon Steel and AISI 304 Stainless Steel Dissimilar Welds", Materials Research, 17, pp. 106-114, (2014).
7. Shojaati, M. and Beidokhti, B., "Characterization of AISI 304/AISI 409 Stainless Steel Joints Using Different Filler Materials", Construction and Building Materials, 147, pp. 608-615, (2017).
8. شفیعیان، جواد، صائب نوری، احسان، و جعفرزادگان، مصطفی، "بررسی ارتباط ریزساختار و مقاومت به خوردگی جوش غیر‌هم‌جنس فولاد زنگ‌نزن 304 و فولاد سادۀ کربنی st37 به‌روش جوش‌کاری اغتشاشی اصطکاکی"، فصل‌نامۀ علوم و مهندسی خوردگی، شماره 8، صفحه 7-20، (1393).
9. مصطفائی، محمد علی، سرکاری خرمی، محمود، پور علی اکبر، حسام،  و کوکبی، امیرحسین، "بررسی ریز ساختار و خواص مکانیکی اتصال غیرهم‌جنس فولاد زنگ‌نزن فریتی به فولاد سادۀ کم کربن"، چهارمین همایش مشترک انجمن مهندسان متالورژی و جامعه علمی ریخته‌گری ایران، دانشگاه علم و صنعت ایران، تهران، (1389).
10. Gou, N.N., Zhang, J.X., Zhang, L.J., Li, Z.G. and Bi, Z.Y., "Single Pass Fiber Laser Butt Welding of Explosively Welded 2205/X65 Bimetallic Sheets and Study on the Properties of the Welded Joint", The International Journal of Advanced Manufacturing Technology, Vol. 86, pp. 2539-2549, (2016).
11. Zhang, L., Pei, Q., Zhang, J.X., Bi, Z.Y. and Li, P.C., "Study on the Microstructure and Mechanical Properties of Explosive Welded 2205/X65 Bimetallic Sheet", Materials and Design, Vol. 64, Article 462476, (2014).
12. Gou, N.N., Zhang, L.J. and Zhang, J.X., "Increased Quality and Welding Efficiency of Laser Butt Welding of 2205/X65 Bimetallic Sheets with a Lagging MIG Arc", Journal of Materials Processing Technology, Vol. 251, pp. 83-92, (2018).
13. Sayiram, G. and Arivazhagan, N., "Microstructural Characterization of Dissimilar Welds between Incoloy 800H and 321 Austenitic Stainless Steel", Materials Characterization, Vol.102, pp. 180-188, (2015).
14. Sharma, S., Taiwade, R.V. and Vashishtha, H., "Investigation on the Multi-Pass Gas Tungstenarc Welded Bi-Metallic Combination between Nickel-Based Superalloy and Ti-Stabilized Austenitic Stainless Steel", Journal of Materials Research, Vol. 32, pp. 3055-3065, (2017).
15. www.yazd-electrode.com, (Acsessed 2021).
16. Folkhard, E., "Welding Metallurgy of Austenitic Stainless Steels", Springer., Vienna, pp. 197-222, (1988).
17. Feng, Y., Luo, Z., Liu, Z., Li, Y., Luo, Y. and Huang, Y., "Keyhole Gas Tungsten arc Welding of AISI 316L Stainless Steel", Materials & Design, Vol. 85, pp. 24-31, (2015).