The Study of Fatigue Behavior of Glass Fiber Reinforced epoxy(GFRP) Composite Under Different Stress Levels

مهندسی متالورژی و مواد

Article 1, Volume 33, Issue 2 - Serial Number 26, September 2022, Pages 1-12   

Document Type: Original Article

DOI: 10.22067/jmme.2022.72975.1029

Authors

alireza moghaddas mousavi zadeh; Ahad Zabett; ُSamane Sahebian^*

Department of Material Science and Engineering, Ferdowsi university of Mashhad, Mashhad, Iran.

Abstract

The aim of this study is to investigate the fatigue behavior of GFRP composite with biaxial fiber orientation [0,90] under different stress levels. First, the tensile test was performed and the UTS value was 420 MPa. Then, fatigue test was performed at 4 stress levels of 70, 50, 42 and 35% of UTS. Fatigue results had acceptable dispersion and the fitting curve on the data also matched well. Finally, the fatigue failure structures of 70 and 35% of UTS samples, using scanning electron microscopy (SEM) were evaluated. The results showed that in both 70 and 35% samples, the mechanism of pull out fibers was obsvered but its intensity was higher in 35% sample. Also in the 35% sample, significant distortion was observed which was absent in the 70% sample. On the other hand, the brittle failure of matrix was more pronounced in the 70% sample than in the 35% sample. This can be related to the increase of the matrix softness due to the application of cyclic load.

Keywords

GFRP Composite; fatigue; epoxy; glass fiber

References

 

1. یوسف محمدی نژاد، "انرژی پاک نیاز و ضرورت هزارهی سوم"، انتشارات نگارنده دانش تهران، (1392).
2. L. Panwara, S.C. Kaushik, Surendra Kotharia., "Role of renewable energy sources in environmental protection: A review", Renewable and Sustainable Energy Reviews 15, India (2011).
3. Richa Kothari,V.V. Tyagi, Ashish Pathak., "Waste-to-energy: A way from renewable energy sources to sustainable development", Sustainable Energy Reviews 14, India (2010).
4. Balat M., "Review of modern wind turbine technology", Energy Sources, Part A: Recovery, Utilization, and Environmental Effects, Vol. 31, 17, (2009).
5. Balat M,. "Usage of energy sources and environmental problems", Energy Exploration and Exploitation, 23, No. 2, (2005).
6. Mayer RM., "Design of composite structures against fatigue applications to wind turbine blades", Chippenham, Antony Rowe Ltd, pp. 195–208, (1996).
7. Kong C, Kim H, Kim J., "A study on structural and aerodynamic design of composite blade for large scale HAWT system", Final report, Hankuk Fiber Ltd, (2000).
8. Yang , D. Sun., "Testing inspecting and monitoring technologies for wind turbine blades: A survey", Renewable and Sustainable Energy Reviews, pp 515-526. Vol. 22, (2013).
9. Bakis, L.C. Bank, V. Brown, E. Cosenza, J. Davalos, J. Lesko, et al., "Fiber reinforced polymer composites for construction-state-of-the-art review", Journal of Composoties, Vol. 6, No. 2, (2002).
10. D. Sims ,W. R. Broughton., "Glass Fiber Reinforced Plastics- Properties", National Physical Laboratory. Tiddington, UK.
11. Douglas S. Cairns, John D Shramstad., "Evaluation of Hand Lay-up And Resin Transfer Molding in Composite Wind Turbine Blade Structures", Sandia Online labratories, (2012).
12. P. Dyer and D. H. Isaac., "Fatigue behavior of continuous glass fiber reinforced composites", Composites Part B: Engineering,Vol .29,No. 6, pp.725-733, (1998)
13. Joris Degrieck and Wim Van Paepegem., "Fatigue damage modeling of fibre-reinforced composite materials: Review", Mechanical Review, Vol. 54, No. 4, (2001).
14. Hemanth Kumar C, R.P. Swamy., "Fatigue life prediction of glass fiber reinforced epoxy composites using artificial neural networks",Composites Communications, Vol. 26, (2021).
15. ASTM D3039, Standard Test Method for Tensile Properties of Polymer Matrix Composite Materials.
16. ASTM D3479, Standard Test Method for Tension-Tension Fatigue of Polymer Matrix Composite Materials.
17. Neil Kelly Wahl., "Spectrum fatigue lifetime and residual strength for fiberglass laminates", A dissertation submitted in partial fulfillment of the requirements for the degree of Doctor of Philosophy in Mechanical Engineering, Montana, (2001).
18. نادیا نصرتی، "بررسی رفتار خزشی کامپوزیت اپوکسی/الیاف شیشه به کار رفته در ساخت پره توربین بادی"، پایان‌نامه کارشناسی ارشد، دانشگاه فردوسی مشهد، (1396).
19. Kalyan Kumar Singh, Md. Touhid Alam Ansari, Md. Sikandar Azam., "Fatigue life and damage evolution in woven GFRP angle ply laminates", International Journal of Fatigue, Vol 142, (2021).
20. مهران طغرایی، "بررسی رفتار خستگی کامپوزیت زمینه پلیمری تقویت شده با الیاف شیشه ساخته شده به دو روش لایه گذاری دستی و تزریق رزین به کمک خلأ (VIP)"، پایان نامه کارشناسی ارشد، دانشگاه فردوسی مشهد (1393).
21. Wahid Ferdous, Allan Manalo, Joshua Peauril, Choman Salih, Kakarla Raghava Reddy, Peng Yu, Peter Schubel, Tom Heyer, "Testing and modelling the fatigue behavior of GFRP composites, Effect of stress level, stress concentration and frequency", Engineering Science and Technology, an International Journal, Vol. 23, No. 5, pp. 1223-1232, (2020).