The effect of age hardening heat treatment (T6) on the microstructure and wear behavior of Al-8Zn-3Mg-2.5Cu nanocomposite reinforced with graphene nano plates

مهندسی متالورژی و مواد

Article 2, Volume 33, Issue 4 - Serial Number 28, December 2022, Pages 13-26   

Document Type: Original Articles

DOI: 10.22067/jmme.2022.78198.1070

Author

Mohammad Alipour^*

Faculty of Mechanical engineering, Department of Materials Engineering, University of Tabriz, Iran

Abstract

In this study, microstructure and wear behavior of Al-8Zn-3Mg-2.5Cu aluminum alloy matrix nanocomposite reinforced with 0.1, 0.3, 0.5, 0.7 and 1 wt.% graphene nano plates (GNPs) produced by stir casting and ultrasonic treatment have been investigated. Ultrasound device equipped with a cooling system with high powers was used for mixing alloy and nanoparticles. Also the microstructure and wear surfaces of nanocomposite was investigated by scanning electron microscope equipped with EDS analysis. The microstructural studies of the nanocomposite revealed that GNPs addition reduces the grain size, but adding high GNPs content (1 wt.%) does not change the grain size considerably. Further investigations on wear revealed that the addition of GNPs increases wear resistance . At high GNPs contents (1 wt.%), the presence of GNPs agglomerate on grain boundaries was found that causes decrease the wear resistance. The optimum amount of nanoparticles is 0.5 wt.% GNPs that nanocomposite exhibits bes wear resistance.

Keywords

Casting nanocomposite; Graphene nano plates; Stir casting; Ultrasonic treatment

References

[1] S. Rawal, "Metal-matrix composites for Space Applications", Journal of The Minerals, Metals & Materials Society, vol. 53, pp 14-17, (2001).

[2] X. Li, Y. Yang, X. Chen," Ultrasonic-Assisted Fabrication of Metal Matrix Nanocomposites", Journal of Materials Science, vol. 39, pp 3211-3212, (2004).

[3] X. Yibin, T. Yoshita, “Thermal Conductivity of SiC Fine Particles Reinforced Al Alloy Matrix Composite With Dispersed Particle Size", Journal of Applied Physics, vol. 95, pp 722-726, (2004).

 [4] C. Borgonovo, D. Apelian, "Manufacture of Aluminum Nanocomposites: A Critical Review", Materials Science Forum, vol. 678, pp 1-22, (2011).

[5] Y. Yang, X. Li, J. Lan, " Study on Bulk Aluminum Matrix Nano-Composite Fabricated by Ultrasonic Dispersion of Nano-Sized SiC Particles in Molten Aluminum Alloy", Materials Science and Engineering A, vol. 380, pp 378-383, (2004).

[6] D. Miracle,"Metal matrix composites–from science to technological significance", Composites Science and Technology, vol. 65, pp 2526-2540, (2005).

[7] L. Wenzhen, L. Shiying, Z. Qiongyuan, Z. Xue,"Ultrasonic-Assisted Fabrication of SiC Nanoparticles Reinforced Aluminum Matrix Composites", Materials Science Forum, vol. 654-656, pp 990-993, (2010).

[8] J.Y. Hihn, M.L. Doche, A. Mandroyan, L. Hallez and B.G. Pollet, "Respective Contribution of Cavitation and Convective Flow to Local Stirring in Sonoreactors", Ultrasonics Sonochemistry, vol. 18, p. 881-887, (2011).

[9] Y. Chen, S. Tekumalla, Y.B. Guo, R. Shabadi, M. Gupta, “The dynamic compressive response of a high-strength magnesium alloy and its nanocomposite", Materials Science and Engineering: A, vol. 702, , pp. 65-72, (2017).

[10] Santanu Sardar, Santanu Kumar Karmakar, Debdulal Das, "Ultrasonic Assisted Fabrication of Magnesium Matrix Composites: AReview", Materials Today: Proceedings, vol. 4, Issue 2, Part A, pp. 3280-3289, (2017).

[11] Deborah D. L. Chung, " Metal-Matrix Composites", Carbon Composites (Second Edition), pp. 532-562, (2017).

[12] G.E. Dieter, "Mechanical Metallurgy" ,Third Edition , McGraw-Hill , (1976).

[12] L.M. Hutchings, Tribology: Friction and wear of engineering materials: Edward Arnold, (1992).

[13] A. Alizadeh, "Mechanical properties and wear behavior of Al–2 wt.% Cu alloy composites reinforced by B₄C nanoparticles and fabricated by mechanical milling and hot extrusion Materials characterization", vol. 67, pp.119–128, (2012).

[14] A.K. Prasada Rao, Karabi Das, B.S. Murty, M. Chakraborty, Effect of grain refinement on wear properties of Al and Al–7Si alloy, Wear, vol. 257, pp. 148-153.( 2004).

[15] X.S. Guan, Z.F. Dong and D.Y. Li, "Surface nanocrystallization by sandblasting and annealing for improved mechanical and tribological properties", Nanotechnology, vol. 16, pp. 2963-2971.( 2005).

[16] A. Shafiei-Zarghani, S.F. Kashani-Bozorg, A. Zarei- Hanzaki, "Wear assessment of Al/Al₂O₃ nano-composite surface layer produced using friction stir processing", Wear, vol. 270, pp. 403-412.( 2011).

[17] T. Ma, H. Yamaura, D.A. Koss, R.C. Voigt, Dry sliding wear behaviour of cast SiC reinforced Al MMCs, Mater. Sci. Eng. A. vol. 360, pp. 116–125.( 2003).

[18] D. Poirier, R.A.L. Drew, M.L. Trudeau, R. Gauvin, "Fabrication and properties of mechanically milled alumina/aluminum nanocomposites", Materials Science and Engineering: A, vol. 527, pp. 7605-7614, ( 2010).

[19] A.H. Yaghtin, E. Salahinejad, A. Khosravifard, "Processing of nanostructured metallic matrix composites by a modified accumulative roll bonding method with structural and mechanical considerations", International Journal of Minerals, Metallurgy, and Materials, vol. 19, pp. 951-956.( 2012).

[20] A. Zolriasatein, R.A. Khosroshahi, M. Emamy, N. Nematie, "Mechanical and wear properties of Al-Al₃Mg₂ nanocomposites prepared by mechanical milling and hot pressing", International Journal of Minerals, Metallurgy and Materials, vol. 20, pp. 290-297.( 2013).

[21] M. Walczak, D. Pieniak, M. Zwierzchowski, "The tribological characteristics of SiC particle reinforced aluminium composites", Archives of Civil and Mechanical Engineering, vol. 15, pp. 116-123.( 2015).