Investigating the wear behavior of nanocomposite based on Cu-5Zn alloy reinforced with carbon nanotubes

مهندسی متالورژی و مواد

Article 7, Volume 34, Issue 4 - Serial Number 32, December 2023, Pages 1-16   

Document Type: Original Articles

DOI: 10.22067/jmme.2023.80885.1103

Author

Mohammad Alipour^*

Faculty of Mechanical engineering, Department of Materials Engineering, University of Tabriz, Iran

Abstract

In the present work we report the development of carbon nanotube reinforced copper-zinc alloy nanocomposites. The carbon nanotubes were used in both uncoated and nickel coated conditions to reinforce copper matrix. The nanocomposites with different carbon nanotubes (0.25 to 1.0) weight percentage were developed using a combination of ultrasonication, ball milling and sintering processes. The developed nanocomposites were subjected to microstructural characterization using scanning and transmission electron microscopes to observe the dispersion of carbon nanotubes. The effect of carbon nanotubes on friction and wear properties of copper nanocomposites were studied using pin on disc testing rig as per ASTM G99 standard. The coefficient of friction of both 1 wt% uncoated and nickel coated carbon nanotubes reinforced nanocomposites was found when compared to copper-zinc alloy. Similarly the wear rate of nanocomposites were found to decrease with the incoporation of carbon nanotubes. The low coefficient of friction and wear rate were attributed to uniform dispersion of carbon nanotubes and formation of carbonaceous layer on the surface of nanocomposites during dry sliding wear.

Keywords

Carbon Nanotubes; Copper; Friction and wear; Nanocomposites

References

 

[1]   F. Rikhtegar, S. Shabestari, H. Saghafian, "Investigation of microstructure and mechanical properties of Al2024-CNT nanocomposite produced by flake powder metallurgy process", In Persian, Journal of Science and Technology of Composites, Vol. 4, No. 1, pp. 91-100, 2017.

[2]   S. Mirzamohammadi, H. Khorsand, M. Aliofkhazraei, "Mechanical behavior of Ni-Al2O3 nanocomposite coatings electroplated in the precence of organic compounds", In Persian, Journal of Science and Technology of Composites, Vol. 4, No. 3, pp. 245-254, 2017.

[3]   M. Dinulović, B. Rašu, "Dielectric modeling of multiphase composites", Composite Structures, Vol. 93, Issue 12, pp. 3209- 3215, 2011.

[4]   Neha Arora, N.N. Sharma, " Arc discharge synthesis of carbon nanotubes: Comprehensive review ", Diamond and Related Materials,  Vol. 50, pp. 135-150, 2014.

 [5] C.G. Kaufmann, R.Y.S.Zampiva, C.P.Bergmann, A. K.Alves, S.R. Mortari, A.Pavlovic, "Production of multi-wall carbon nanotubes starting from a commercial graphite pencil using an electric arc discharge in aqueous medium", FME Transactions, Vol. 46, pp. 151-156, 2018.

[6]   P. J. F.Harris, "Carbon nanotube science", Cambridge University Press, New York, 2009.

[7]   P.W.R.Beaumont, C. Soutis, and A.Hodzic, "Structural integrity and durability of advanced composites: Innovative modelling methods and intelligent design", Elsevier, Cambridge, UK, 2015.

[8]   G.Overney, W.Zhong, D.Tomanek, "Structural rigidity and low-frequency vibrational-modes of long carbon tubules", Zeitschrift für Physik / D: Atoms, molecules and clusters, Vol. 27, pp. 93-96, 1993.

[9]   J.P.Lu, "Elastic properties of carbon nanotubes and nanoropes", Physical Review Letters, Vol. 79, pp. 1297- 1300, 1997.

[10] M.M.J.Treacy, T.W.Ebbesen and J.Gibson, "Exceptionally high Young’s modulus observed for individual carbon nanotubes", Nature, Vol. 381, pp. 678-680, 1996.

[11] P.G.Koppad, V.K.Singh, C.S.Ramesh, R.G.Koppad and K.T.Kashyap, "Metal matrix nanocomposites reinforced with carbon nanotubes", In: Tiwari, A., Shukla, S.K. (Eds.): Advanced Carbon Materials and Technology, John Wiley & Sons, Inc., Hoboken, pp. 331-376, 2013.

[12] G.Qianming, Li Dan, L Zhi, Y.Xiao-Su , L.Ji, "Tribology properties of carbon nanotube-reinforced composites, In: Friedrick, K., Schlarb, A.K. (Eds.)", Tribology and Interface Engineering Series, Vol. 55, pp. 245-267, 2008.

[13] H. M.Mallikarjuna, C. S.Ramesh, P. G.Koppad, R.Keshavamurthy and K.T Kashyap, "Effect of carbon nanotube and silicon carbide on microstructure and dry sliding wear behavior of copper hybrid nanocomposites", Trans. Nonferrous Met. Soc. China, Vol. 26, pp. 3170-3182, 2016.

[14] H. M.Mallikarjuna, K. T.Kashyap, P. G Koppad, C. S.Ramesh, R.Keshavamurthy,"Microstructure and dry sliding wear behavior of Cu-Sn alloy reinforced with multiwalled carbon nanotubes", Trans. Nonferrous Met. Soc. China, Vol. 26, pp. 1755-1764, 2016.

[15] P. G.Koppad, K. T.Kashyap, V.Shrathinth, T. A.Shetty, R. G.Koppad, "Microstructure and microhardness of carbon nanotube reinforced copper nanocomposites", Materials Science and Technology, Vol. 29, pp. 605-609, 2013.

[16] P. G.Koppad, H. R.Aniruddha Ram, K. T Kashyap, "On shear-lag and thermal mismatch model in multiwalled carbon nanotube/copper matrix nanocomposites", Journal of Alloys and Compounds., Vol. 549, pp. 82-87, 2013.

[17] P. G.Koppad, H. R. A.Ram, C. S.Ramesh,  K. T.Kashyap, R. G. Koppad, "On thermal and electrical properties of multiwalled carbon nanotubes/copper matrix nanocomposites", Journal of Alloys and Compounds, Vol. 580, pp. 527-532, 2013.

[18] R.George, K. T.Kashyap, R.Rahul, S.Yamdagni, "Strengthening in carbon nanotube/aluminium (CNT/Al) composites", Scripta Materialia 53, pp. 1159- 1163, 2005.

[19] H. R. A.Ram, P. G.Koppad, K. T.Kashyap, "Nanoindentation studies on MWCNT/aluminum alloy 6061 nanocomposites", Materials Science and Engineering: A, Vol. 559, pp. 920-923, 2013.

[20] K. T.Kashyap, K. B.Puneeth, A.Ram, P. G.Koppad, "Ageing kinetics in Carbon nanotube reinforced Aluminium alloy AA6063", Materials Science Forum, Vol. 710, pp. 780-785, 2012.

[21] J. P.Tu, Y. Z Yang, L. Y.Wang, X. C.Ma, X. B.Zhang, "Tribological properties of carbon-nanotube- reinforced copper composites", Tribology Letters, Vol. 10 pp. 225-228, 2001.

[22] K. T.Kim, S. I.Cha, S. H.Hong, S. H.Hong, "Microstructures and tensile behavior of carbon nanotubes reinforced Cu matrix nanocomposites", Materials Science and Engineering: A, Vol. 430, pp. 27-33, 2006.

[23] Y.A.Sorkhe, H. Aghajani, A.Taghisadeh Tabrizi, "Synthesis and characterisation of Cu–TiO2 nanocomposite produced by thermochemical process, Powder Metallurgy", Powder Metallurgy, pp. 107-111, 2016.

[24] G.Naseri Azari Golnaz, A.Taghizadeh Tabrizi, , H.Aghajani, "Investigation on corrosion behavior of Cu–TiO2 nanocomposite synthesized by the use of SHS method", Journal of Materials Research and Technology, Vol. 8, Issue 2, pp. 2216-2222, 2019.

 [25] S.A.N.Mehrabani, A.T.Tabrizi, H.Aghajani and H.Pourbagheri, "Corrosion Behavior of SHS-Produced Cu–Ti–B Composites", International Journal of Self-Propagating High-Temperature Synthesis, Vol. 29, No. 3, pp. 167–172, 2020.

[26] H.Aghajani, M.Roostaei, S.Sharif Javaherian, A.Taghizadeh A.Tabrizi, Abdoli Silabi, N.Farzam Mehr, "Wear behavior of self-propagating high-temperature synthesized Cu-TiO2 nanocomposites", Synthesis and Sintering, Vol. 1, no. 3, pp. 127-134, 2021.

 [27] C.B.Lin, Z.Chang, Y. H.Tunga, K. Ko, "Manufacturing and tribological properties of copper matrix/carbon nanotubes composites", Wear, Vol. 270, pp 382-394, 2011.

[28] Z.Huang, Z.Zheng, S.Zhao, S.Dong, P.Luo, L.Chen, "Copper matrix composites reinforced by aligned carbon nanotubes: Mechanical and tribological properties", Materials and Design, Vol. 133, pp 570-578, 2017.

[29] E.Dujardin, T. W.Ebbesen, H.Hiura and K.Taigaki, "Capillarity and wetting of carbon nanotubes", Science, Vol. 265, pp 1850-1852, 1994.

[30] K.Rajkumar, S.Aravindan, "Tribological characteristics of copper-nano carbon crystalline composites", In: Tyagi, R., Davim, J.P. (Eds.): Processing techniques and tribological behaviour of composite materials. IGI Global, Hershey, pp. 107-125, 2015.

[31] P.Manikandan, R.Sieh, A.Elayaperumal, H. R.Le, S. Basu, "Micro/Nanostructure and tribological characteristics of pressureless sintered carbon nanotubes reinforced aluminium matrix composites", Journal of Nanomaterials, Article ID 9843019, 2016.

[32] K. Rajkumar, S. Aravindan., “Tribological performance of microwave sintered copper–TiC–graphite hybrid composites", Tribology International, Vol. 44, no. 4, PP. 347-358, 2011.

 [33] C. S.Ramesh, N.Ahmed, M. A.Mujeebu, M. Z.Abdullah, "Development and performance analysis of novel cast copper–SiC–Gr hybrid composites", Materials and Design, Vol. 30(6), pp. 1957-1965, 2009.

[34] C. A. V.Kumar, J. S.Rajadurai, "Influence of rutile (TiO2) content on wear and microhardness characteristics of aluminium-based hybrid composites synthesized by powder metallurgy", Transactions of Nonferrous Metals Society of China, Vol. 26, pp 63-73, 2016.

[35] G.Gautam, N Kumar, A.Mohan, R. K.Gautam, S.Mohan, "Tribology and surface topography of tri-aluminide reinforced composites", Tribology International, Vol. 97, pp 49-58, 2016.

[36]  H. M.Mallikarjuna, C. S.Ramesh, P. G.Koppad, R. Keshavamurthy, K. T. Kashyap, "Effect of carbon nanotube and silicon carbide on microstructure and dry sliding wear behavior of copper hybrid nanocomposites", Transactions of Nonferrous Metals Society of China, Vol. 26, pp 3170-3182, 2016.

[37] Jalal Jafari, Mohammad Kazem Besharati Givi & Mohsen Barmouz," Mechanical and microstructural characterization of Cu/CNT nanocomposite layers fabricated via friction stir processing", The International Journal of Advanced Manufacturing Technology, Vol. 78, pp. 199-209, 2015.

 [38] M.Ruiz-Andrés, A.Conde, de J.,Damborenea, I.García, "Wear behavior of aluminum alloys at slow sliding speeds", Tribology Transactions, Vol. 58, pp. 955-962, 2015.

[39] K. R.Kumar, K. M.Mohanasundaram, G.Arumaikkannu, R.Subramanian, "Analysis of parameters influencing wear and frictional behavior of aluminum–fly ash composites", Tribology Transactions, Vol. 55, pp 723-729, 2012.

[40] K.Rajkumar, S.Aravindan, "Tribological studies on microwave sintered copper carbon nanotube composites", Wear, Vol. 270, pp 613-621, 2011.

[41] B.Chen, J.Yang, Q Zhang, H.Huang, H. Li, H.Tang, C.Li, "Tribological properties of copper-based composites with copper coated NbSe2 and CNT", Materials and Design, Vol. 75, pp. 24-31, 2015.

[42] C. H Guiderdoni, C.Estournes, A.Peigney, A. Weibel, V.Turq, C. H.Laurent, "The preparation of double-walled carbon nanotube/Cu composites by spark plasma sintering and their hardness and friction properties", Carbon, Vol. 49, pp 4535-4543, 2011.

[43] S. R.Dong, J. P.Tu, X. B.Zhang, "An investigation of the sliding wear behavior of Cu-matrix composite reinforced by carbon nanotubes", Materials Science and Engineering A, Vol. 313, pp 83-87, 2001.