The Effect of Cold Rolling on the Microstructure and Texture Evolution of API 5L X70 Steel in Normal and 45° Tilted Cross Section

مهندسی متالورژی و مواد

Article 5, Volume 35, Issue 3 - Serial Number 35, October 2024, Pages 67-82   

Document Type: Original Articles

DOI: 10.22067/jmme.2024.87104.1146

Authors

Seyed Hossein Hosseini Mortazavi; Mostafa Mirjalili^* ; Mohammad Hadi Moayed; gholamreza ebrahimi; Ghasem Barati Darband

Department of Materials and Metallurgical Engineering, Faculty of Engineering, Ferdowsi University of Mashhad, Mashhad, Iran.

Abstract

In the present study, a combination of X-ray diffraction spectroscopy, field emission scanning electron microscopy (FESEM) and optical microscopy methods were used to investigate the microstructure and crystallographic texture changes of API 5L X70 pipeline steel following an extreme cold working process that resulted in reduce the thickness of 80% in the sample. All investigations were done on two different sections of the sample, including the surface and the inclined section rotated 45 degrees relative to the surface. In fact, these two cross-sections are chosen to show the angle between the two important crystallographic planes of {100} and {110}. FESEM and optical microscope analyzes showed that the microstructure of the primary steel includes granular bainite, conventional upper bainite, and martensite-austenite islands. The results showed that the morphology of the initial microstructure consisted of mostly equiaxed grains, which after applying cold work due to being subjected to severe pressure, turns into a microstructure with the morphology of elongated grains, especially in the rotated section. Analysis of crystal orientation changes by X-ray diffraction spectroscopy showed that the density of {100} crystallographic planes decreased due to applied cold work on the surface and at the same time the density of {110} crystallographic planes on the surface increased. Also, the results proved that {100} crystallographic planes were replaced by {110} crystallographic planes on the sample rotated by 45 degrees.

Keywords

X70 steel; cold rolling; texture; microstructure; grain boundary

References

[1] H. Tamehiro, T. Takeda, S. Matsuda, K. Yamamoto, and N. Okumura, "Effect of Accelerated Cooling after Controlled Rolling on the Hydrogen Induced Cracking Resistance of Line Pipe Steel," Transactions of the Iron and Steel Institute of Japan, vol. 25, no. 9, pp. 982-988, 1985. https://doi.org/10.2355/isijinternational1966.25.982

[2] E. Ohaeri, U. Eduok, and J. Szpunar, "Relationship between microstructural features in pipeline steel and hydrogen assisted degradation," Engineering Failure Analysis, vol. 96, pp. 496-507, 2019. https://doi.org/10.1016/j.engfailanal.2018.11.008

[3] M. A. Mohtadi-Bonab, M. Eskandari, K. M. M. Rahman, R. Ouellet, and J. A. Szpunar, "An extensive study of hydrogen-induced cracking susceptibility in an API X60 sour service pipeline steel," International Journal of Hydrogen Energy, vol. 41, no. 7, pp. 4185-4197, 2016. https://doi.org/10.1016/j.ijhydene.2016.01.031

[4] M. Eskandari, M. A. Mohtadi-Bonab, and J. A. Szpunar, "Evolution of the microstructure and texture of X70 pipeline steel during cold-rolling and annealing treatments," Materials & Design, vol. 90, pp. 618-627, 2016. https://doi.org/10.1016/j.matdes.2015.11.015

[5] C. Lesch, N. Kwiaton, and F. B. Klose, "Advanced High Strength Steels (AHSS) for Automotive Applications − Tailored Properties by Smart Microstructural Adjustments," steel research international, vol. 88, no. 10, pp. 1700210, 2017. https://doi.org/10.1002/srin.201700210

[6] F. G. Caballero, H, Roelofs, St. Hasler, C. Capdevila, J. Chao, J. Cornide, and C. Garcia-Mateo, "Influence of bainite morphology on impact toughness of continuously cooled cementite free bainitic steels," Materials Science and Technology, vol. 28, no. 1, pp. 95-102, 2012. https://doi.org/10.1179/1743284710Y.0000000047

[7] E. Sadeghi Meresht, T. Shahrabi Farahani, and J. Neshati, "Failure analysis of stress corrosion cracking occurred in a gas transmission steel pipeline," Engineering Failure Analysis, vol. 18, no. 3, pp. 963-970, 2011. https://doi.org/10.1016/j.engfailanal.2010.11.014

[8] M. A. Mohtadi-Bonab, J. A. Szpunar, and S. S. Razavi-Tousi, "Hydrogen induced cracking susceptibility in different layers of a hot rolled X70 pipeline steel," International Journal of Hydrogen Energy, vol. 38, no. 31, pp. 13831-13841, 2013. https://doi.org/10.1016/j.ijhydene.2013.08.046

[9] Y. Baik and Y. Choi, "The effects of crystallographic texture and hydrogen on sulfide stress corrosion cracking behavior of a steel using slow strain rate test method," The Physics of Metals and Metallography, vol. 115, no. 13, pp. 1318-1325, 2014. https://doi.org/10.1134/S0031918X14130031

[10] E. Fallahmohammadi, F. Bolzoni, G. Fumagalli, G. Re, G. Benassi, and L. Lazzari, "Hydrogen diffusion into three metallurgical microstructures of a C–Mn X65 and low alloy F22 sour service steel pipelines," International Journal of Hydrogen Energy, vol. 39, no. 25, pp. 13300-13313, 2014. https://doi.org/10.1016/j.ijhydene.2014.06.122

[11] M. A. Mohtadi-Bonab, M. Eskandari, and J. A. Szpunar, "Texture, local misorientation, grain boundary and recrystallization fraction in pipeline steels related to hydrogen induced cracking," Materials Science and Engineering: A, vol. 620, pp. 97-106, 2015. https://doi.org/10.1016/j.msea.2014.10.009

[12] M. A. Mohtadi-Bonab, J. A. Szpunar, R. Basu, and M. Eskandari, "The mechanism of failure by hydrogen induced cracking in an acidic environment for API 5L X70 pipeline steel," International Journal of Hydrogen Energy, vol. 40, no. 2, pp. 1096-1107, 2015. https://doi.org/10.1016/j.ijhydene.2014.11.057

[13] R. A. Oriani and P. H. Josephic, "Hydrogen-enhanced load relaxation in a deformed medium-carbon steel," Acta Metallurgica, vol. 27, no. 6, pp. 997-1005, 1979. https://doi.org/10.1016/0001-6160(79)90187-1

[14] A. H. S. Bueno, E. D. Moreira, and J. A. C. P. Gomes, "Evaluation of stress corrosion cracking and hydrogen embrittlement in an API grade steel," Engineering Failure Analysis, vol. 36, pp. 423-431, 2014. https://doi.org/10.1016/j.engfailanal.2013.11.012

[15] E. Ohaeri, J. Szpunar, F. Fazeli, and M. Arafin, "Hydrogen induced cracking susceptibility of API 5L X70 pipeline steel in relation to microstructure and crystallographic texture developed after different thermomechanical treatments," Materials Characterization, pp. 142-156, 2018. https://doi.org/10.1016/j.matchar.2018.08.034

[16] J. A. Lee, D. H. Lee, M. Y. Seok, U. B. Baek, Y. H. Lee, S. H. Nahm, and J. I. Jang, "Hydrogen-induced toughness drop in weld coarse-grained heat-affected zones of linepipe steel," Materals Chara Cterization, vol. 82, 2013/08 2013. https://doi.org/10.1016/j.matchar.2013.05.001

[17] A. J. Haq, K. Muzaka, D. P. Dunne, A. Calka, and E. V. Pereloma, "Effect of microstructure and composition on hydrogen permeation in X70 pipeline steels," International Journal of Hydrogen Energy, vol. 38, no. 5, pp. 2544-2556, 2013. https://doi.org/10.1016/j.ijhydene.2012.11.127

[18] D. Hejazi, A. J. Haq, N. Yazdipour, D. P. Dunne, A. Calka, F. Barbaro, and E. V. Pereloma, "Effect of manganese content and microstructure on the susceptibility of X70 pipeline steel to hydrogen cracking," Materials Science and Engineering: A, vol. 551, pp. 40-49, 2012. https://doi.org/10.1016/j.msea.2012.04.076

[19] J. Moon, C. Park, and S.-J. Kim, "Influence of Ti addition on the hydrogen induced cracking of API 5L X70 hot-rolled pipeline steel in acid sour media," Metals and Materials International, vol. 18, no. 4, pp. 613-617, 2012. https://doi.org/10.1007/s12540-012-4007-x

[20] V. Venegas, F. Caleyo, T. Baudin, J. H. Espina-Hernández, and J. M. Hallen, "On the role of crystallographic texture in mitigating hydrogen-induced cracking in pipeline steels," Corrosion Science, vol. 53, no. 12, pp. 4204-4212, 2011. https://doi.org/10.1016/j.corsci.2011.08.031

[21] C. Junjia, G. Sun, J. Xu, X. Huang, and G. Li, "A method to evaluate the formability of high-strength steel in hot stamping," Materials and Design, vol. 77, pp. 95-109, 2015. https://doi.org/10.1016/j.matdes.2015.04.009

[22] S. I. Wright and D. P. Field, "Recent studies of local texture and its influence on failure," Materials Science and Engineering: A, vol. 257, no. 1, pp. 165-170, 1998. https://doi.org/10.1016/S0921-5093(98)00835-1

[23] C. Herrera, N. B. Lima, A. F. Filho, R. L. Plaut, and A. F. Padilha, "Texture and mechanical properties evolution of a deep drawing medium carbon steel during cold rolling and subsequent recrystallization," Journal of Materials Processing Technology, vol. 209, no. 7, pp. 3518-3524, 2009. https://doi.org/10.1016/j.jmatprotec.2008.08.007

[24] A. Ghosh, S. Kundu, and D. Chakrabarti, "Effect of crystallographic texture on the cleavage fracture mechanism and effective grain size of ferritic steel," Scripta Materialia, vol. 81, pp. 8-11, 2014. https://doi.org/10.1016/j.scriptamat.2014.02.007

[25] M. A. Mohtadi-Bonab, R. Karimdadashi, M. Eskandari, and J. A. Szpunar, "Hydrogen-Induced Cracking Assessment in Pipeline Steels Through Permeation and Crystallographic Texture Measurements," Journal of Materials Engineering and Performance, vol. 25, no. 5, pp. 1781-1793, 2016. https://doi.org/10.1007/s11665-016-2021-8

[26] M. A. Arafin, and J. A. Szpunar, "A new understanding of intergranular stress corrosion cracking resistance of pipeline steel through grain boundary character and crystallographic texture studies," Corrosion Science, vol. 51, no. 1, pp. 119-128, 2009. https://doi.org/10.1016/j.corsci.2008.10.006

[27] R. K. Ray, J. J. Jonas, M. P. Butrón-Guillén, and J. Savoie, "Transformation Textures in Steels," ISIJ International, vol. 34, no. 12, pp. 927-942, 1994. https://doi.org/10.2355/isijinternational.34.927

[28] V. Javaheri, N. Khodaie, A. Kaijalainen, and D. Porter, "Effect of niobium and phase transformation temperature on the microstructure and texture of a novel 0.40% C thermomechanically processed steel," Materials Characterization, vol. 142, pp. 295-308, 2018. https://doi.org/10.1016/j.matchar.2018.05.056

[29] J. Li, X. Gao, L. Du, and Z. Liu, "Relationship between microstructure and hydrogen induced cracking behavior in a low alloy pipeline steel," Journal of Materials Science & Technology, vol. 33, no. 13, pp. 1504-1512, 2017. https://doi.org/10.1016/j.jmst.2017.09.013

[30] U. K. Viswanathan, G. K. Dey, and M. K. Asundi, "Precipitation Hardening in 350 Grade Maraging Steel," Metallurgical Transactions A, vol. 24, no. 11, pp. 2429-2442, 1993. https://doi.org/10.1007/BF02646522

[31] M. Masoumi, C. C. Silva, and H. F. G. d. Abreu, "Effect of Rolling in the Recrystallization Temperature Region Associated with a Post-Heat Treatment on the Microstructure, Crystal Orientation, and Mechanical Properties of API 5L X70 Pipeline Steel," Materials Research, vol. 20, no. 1, 2017. https://doi.org/10.1590/1980-5373-MR-2016-0651

[32] M. W. Zhou, and H. Yu, "Effects of precipitates and inclusions on the fracture toughness of hot rolling X70 pipeline steel plates," International Journal of Minerals, Metallurgy, and Materials, vol. 19, no. 9, pp. 805-811, 2012. https://doi.org/10.1007/s12613-012-0632-0

[33] J. Song, and W. A. Curtin, "Mechanisms of hydrogen-enhanced localized plasticity: An atomistic study using α-Fe as a model system," Acta Materialia, vol. 68, pp. 61–69, 2014. https://doi.org/10.1016/j.actamat.2014.01.008

[34] G. W. Hong, and J. Y. Lee, "The interaction of hydrogen and the cementite-ferrite interface in carbon steel," Journal of Materials Science, vol. 18, no. 1, pp. 271-277, 1983. https://doi.org/10.1007/BF00543835

[35] W. Y. Choo, and J. Y. Lee, "Effect of cold working on the hydrogen trapping phenomena in pure iron," Metallurgical Transactions A, vol. 14, no. 7, pp. 1299-1305, 1983. https://doi.org/10.1007/BF02664812

[36] M. A. Mohtadi-Bonab, M. Eskandari, and J. A. Szpunar, "Effect of arisen dislocation density and texture components during cold rolling and annealing treatments on hydrogen induced cracking susceptibility in pipeline steel," Journal of Materials Research, vol. 31, no. 21, pp. 3390-3400, 2016. https://doi.org/10.1557/jmr.2016.357

[37] A. Laureys, T. Depover, R. Petrov, and K. Verbeken, "Microstructural characterization of hydrogen induced cracking in TRIP-assisted steel by EBSD," Materials Characterization, vol. 112, pp. 169-179, 2016. https://doi.org/10.1016/j.matchar.2015.12.017

[38] R. Joodaki, S. R. Alavi Zaree, K. Gheisari, and M. Eskandari, "Effect of Annealing Treatments on the Microstructure and Texture Development in API 5L X60 Microalloyed Pipeline Steel," Journal of Materials Engineering and Performance, vol. 26, pp. 2003-2013, 2017. https://doi.org/10.1007/s11665-017-2673-z

[39] M. Gomez, P. Valles, and S. F. Medina, "Evolution of microstructure and precipitation state during thermomechanical processing of a X80 microalloyed steel," Materials Science and Engineering: A, vol. 528, no. 13-14, pp. 4761-4773, 2011. https://doi.org/10.1016/j.msea.2011.02.087

[40] K. Nishioka, and K. Ichikawa, "Progress in thermomechanical control of steel plates and their commercialization," Science and Technology of Advanced Materials, vol. 13, no. 2, pp. 023001, 2012. https://doi.org/10.1088/1468-6996/13/2/023001

[41] Y. Atsuhiko, H. Morikawa, O. Yasumitsu, and K. Itoh, "Formulation of Static Recrystallization of Austenite in Hot Rolling Process of Steel Plate," Isij International, vol. 27, pp. 425-431, 1987. https://doi.org/10.2355/isijinternational1966.27.425

[42] N. Yazdipour, A. J. Haq, K. Muzaka, and E. V. Pereloma, "2D modelling of the effect of grain size on hydrogen diffusion in X70 steel," Computational Materials Science, vol. 56, pp. 49-57, 2012. https://doi.org/10.1016/j.commatsci.2012.01.003

[43] A. Thomas, and J. Szpunar, "Effect of Cold-Rolling on Hydrogen Diffusion and Trapping in X70 Pipeline Steel," Journal of Engineering Materials and Technology, Transactions of the ASME, vol. 143, no. 3, pp. 031002-031013, 2021. https://doi.org/10.1115/1.4049320

[44] H. M. Ha, J.-H. Ai, and J. R. Scully, "Effects of Prior Cold Work on Hydrogen Trapping and Diffusion in API X-70 Line Pipe Steel During Electrochemical Charging," Corrosion, vol. 70, no. 2, pp. 166-184, 2013. https://doi.org/10.5006/0990

[45] H. Huang, and W. J. D. Shaw, "Electrochemical Aspects of Cold Work Effect on Corrosion of Mild Steel in Sour Gas Environments," Corrosion, vol. 48, no. 11, pp. 931–939, 1992. https://doi.org/10.5006/1.3315896

[46] M. Zhu, X. Li, Zh. Liu, Sh. Wang, T. Zhao, and J. Jia, "Effect of Strength and Microstructure on Stress Corrosion Cracking Behavior and Mechanism of X80 Pipeline Steel in High pH Carbonate/Bicarbonate Solution," Journal of Materials Engineering and Performance, vol. 23, pp. 1358–1365, 2014. https://doi.org/10.1007/s11665-014-0880-4

[47] J. Xu, R. D. K. Misra, B. Guo, Z. Jia, and L. Zheng, "Understanding variability in mechanical properties of hot rolled microalloyed pipeline steels: Process–structure–property relationship," Materials Science and Engineering: A, vol. 574, pp. 94-103, 2013. https://doi.org/10.1016/j.msea.2013.03.017

[48] J. Q. Wang, A. Atrens, D. R. Cousens, P. M. Kelly, C. Nockolds, and S. Bulcock, "Measurement of grain boundary composition for X52 pipeline steel," Acta Materialia, vol. 46, no. 16, pp. 5677-5687, 1998. https://doi.org/10.1016/S1359-6454(98)00246-8

[49] M. Jiang, L. N. Chen, J. He, G. Chen, and C. Li, "Effect of controlled rolling/controlled cooling parameters on microstructure and mechanical properties of the novel pipeline steel," Advances in Manufacturing, vol. 2, pp. 265-274, 2014. https://doi.org/10.1007/s40436-014-0084-z

[50] B. Hwang, Y. M. Kim, S. Lee, N. J. Kim, and J. Y. Yoo, "Correlation of rolling condition, microstructure, and low-temperature toughness of X70 pipeline steels," Metallurgical and Materials Transactions A, vol. 36, no. 7, pp. 1793-1805, 2005. https://doi.org/10.1007/s11661-005-0043-1

[51] H. K. D. H. Bhadeshia, and J. W. Christian, "Bainite in steels," Metallurgical Transactions A, vol. 21, no. 3, pp. 767-797, 1990. https://doi.org/10.1007/BF02656561

[52] S. Zajac, V. Schwinn, and K. H. Tacke, "Characterisation and Quantification of Complex Bainitic Microstructures in High and Ultra-High Strength Linepipe Steels," Materials Science Forum - MATER SCI FORUM, vol. 500-501, pp. 387-394, 2005. https://doi.org/10.4028/www.scientific.net/MSF.500-501.387

[53] B. L. Bramfitt, and J. G. Speer, "A perspective on the morphology of bainite," Metallurgical Transactions A, vol. 21, no. 3, pp. 817-829, 1990. https://doi.org/10.1007/BF02656565

[54] T. Araki, I. Kozasu, H. Tankechi, K. Shibata, M. Enomoto, and H. Tamehiro, "Atlas for bainitic microstructures," ISIJ, Tokyo, Japan, vol. 1, pp. 4-5, 1992.

[55] P. Cizek, B. P. Wynne, C. H. J. Davies, B. C. Muddle, and P. D. Hodgson, "Effect of composition and austenite deformation on the transformation characteristics of low-carbon and ultralow-carbon microalloyed steels," Metallurgical and Materials Transactions A, vol. 33, no. 5, pp. 1331-1349, 2002. https://doi.org/10.1007/s11661-002-0059-8

[56] M. X. Zhang, and P. M. Kelly, "Accurate orientation relationship between ferrite and austenite in low carbon martensite and granular bainite," Scripta Materialia, vol. 47, no. 11, pp. 749-755, 2002. https://doi.org/10.1016/S1359-6462(02)00196-3

[57] G. K. Tirumalasetty, M. A. Van Huis, C. M. Fang, Q. Xu, F. D. Tichelaar, D. N. Hanlon, J. Sietsma, and H. W. Zandbergen, "Characterization of NbC and (Nb,Ti)N nanoprecipitates in TRIP assisted multiphase steels," Acta Materialia, vol. 59, no. 19, pp. 7406-7415, 2011. https://doi.org/10.1016/j.actamat.2011.08.012

[58] S. M. Lee, and J. Y. Lee, "The effect of the interface character of TiC particles on hydrogen trapping in steel," Acta Metallurgica, vol. 35, no. 11, pp. 2695-2700, 1987. https://doi.org/10.1016/0001-6160(87)90268-9

[59] A. Haldar, S. Suwas, and D. Bhattacharjee, “Microstructure and Texture in Steels: and Other Materials,” 2009.

[60] R. K. Ray, J. J. Jonas, and R. E. Hook, "Cold rolling and annealing textures in low carbon and extra low carbon steels," International Materials Reviews, vol. 39, no. 4, pp. 129-172, 1994. https://doi.org/10.1179/imr.1994.39.4.129

[61] M. Koyama, E. Akiyama, T. Sawaguchi, K. Ogawa, I. V. Kireeva, Y. I. Chumlyakov, and K. Tsuzaki, "Hydrogen-assisted quasi-cleavage fracture in a single crystalline type 316 austenitic stainless steel," Corrosion Science, vol. 75, pp. 345–353, 2013. https://doi.org/10.1016/j.corsci.2013.06.018

[62] J. I. Verdeja, J. Asensio, and J. A. Pero-Sanz, "Texture, formability, lamellar tearing and HIC susceptibility of ferritic and low-carbon HSLA steels," Materials Characterization, vol. 50, no. 1, pp. 81-86, 2003. https://doi.org/10.1016/S1044-5803(03)00106-2

[63] D. H. Dwivedi, K. Lepkova, and T. Becker, "Carbon steel corrosion: a review of key surface properties and characterization methods," RSC Advances, vol. 7, no. 8, pp. 4580-4610, 2017. https://doi.org/10.1039/C6RA25094G

[64] S. A. Park, J. G. Kim, Y. S. He, K. S. Shin, and J. B. Yoon, "Comparative study on the corrosion behavior of the cold rolled and hot rolled low-alloy steels containing copper and antimony in flue gas desulfurization environment," The Physics of Metals and Metallography, vol. 115, no. 13, pp. 1285-1294, 2014. https://doi.org/10.1134/S0031918X14130201