Aerodynamic Performance Investigation of an Experimental Variable-Span Morphing Wing Model

علوم کاربردی و محاسباتی در مکانیک

Article 3, Volume 27, Issue 1 - Serial Number 13, March 2016, Pages 35-50   

Document Type: Original Article

DOI: 10.22067/fum-mech.v27i1.38491

Authors

abbas tarabi^{* 1}; sajjad gasemloo²; mahmoud mani²

¹دانشگاه مالک اشتر

²امیر کبیر

Abstract

In this paper, the implementation of the variable-span Morphing wing(VSMW) on the wings of a UAV to achiev the optimal performance for various flight regimes is studied in wind tunnels. For the implementation of this plan, a morphing wing with its related mechanism is designed, built and tested. Tests were carried out at a low- speed wind tunnel with speeds of 35, 60 and 80 m/s in the range of Reynolds Number between 250×〖10〗^3 to 620×〖10〗^3. For the implementation of the morphing wing plan, the maximum deviation of wing span relative to Basewing (BW) is 38 percent and change of aspect ratio is 74% percent. Experimental results showed the improved aerodynamic properties of VSMW compared to BW. These improvements are in the form of reduction of induced drag, thrust required and increasing of lift coefficient, aerodynamic efficiency, endurance and rang. According to the results, endurance and range for VSMW comparison to BW, respectively 17 and 5 percent increased. The experimental studies show that the maximum aerodynamic efficiency of the wing model occurs at 4 degree angle of attack with the maximum value being 14.8 for the base wing, 16.3 for the morphing wing with 50 percent (5 cm) extension in wing span, and 17.4 % for the morphing wing with 100 percent (10 cm) span extension. This research also shows how VSMW can be used as an alternative method of roll control instead of the regular method (i.e. using aileron control surfaces) as it provides more roll control power than the regular method.

Keywords

Morphing Wing; Variable Span; wind tunnel; Range and Endurance; Aerodynamic Coefficient

References

1. Galantai, V.P., "Design and Analysis of Morphing Wing for Unmanned Aerial Vehicles", phD Thesis,Department of Mechanical and Engineering,University of Toronto,(2010).

2. Joshi, S.P., Tidwell, Z., Crossley, W.A. and Ramakrishnan, S., "Comparison of Morphing Wing Strategies Based Upon Aircraft Performance Impacts", 45th AIAA/ASME/ASCE/AHS/ASC Structures, Structural Dynamics & Materials Conference, Palm Springs, California, April 19-22, (2004).

3. SH, M.A. and Kumar, C.A., "A Review of Unmanned Aerial Vehicle and their Morphing Concepts Evolution and Implications for the Present Day Technology", International Journal of Mechanical Engineering and Technology (IJMET), Vol. 4, No. 4, pp. 348-356, July - August (2013).

4. Weisshaar, T.A., "Morphing aircraft technology-new shapes for aircraft design", Purdue Univ Lafayette In, (2006).

5. AeroVisions Inc., http://www.canosoarus.com., Accessed 22 May (2011).

6. Arrison, L., Birocco, K., Gaylord, C., Herndon, B., Manion, K. and Metheny, M., "2002-2003 AE/ME Morphing Wing Design", Spring Semester Final Report, Virginia Tech Aerospace Engineering Senior Design Project, (2003).

7. Neal, D.A., Good, M.G., Johnston, C.O., Robertshaw, H.H., Mason, W.H. and Inman, D.J., "Desing and Wind-Tunnel Analysis of a Fully Adaptive Aircraft Configuration", In: 45th AIAA/ASME/ASCE/AHS/ASC Structures, Structural Dynamics, and Materials Conference, Palm Springs, April 19-22, (2004).

8. Bae, J.S., Seigler, T.M. and Inman, D.J., "Aerodynamic and Static Aeroelastic Characteristics of a Variable-Span Morphing Wing", Journal of Aircraft, Vol. 42, No. 2, pp. 528-534, (2005).

9. Han, C., Lee, S. and Ruy, K., "Experimental Study of a Telescopic Wing Inside Channel", Engineering Notes, Journal of Aircraft, Vol. 44, No. 3, pp. 1029-1030, (2007).

10. Gamboa, P., Aleixo, P., Vale, J., Lau, F. and Suleman, A., "Design and Testing of a Morphing Wing for an Experimental UAV", University of Beria Interior Covilha (Portugal), Nov. (2007).

11. do Vale, J.L., Leite, A., Lau, F. and Suleman, A., "Aero-Structural Optimization and Performance Evaluation of a Morphing Wing with Variable Span and Camber", Journal of Intelligent Material Systems and Structures, vol. 22, 10: pp. 1057-1073., July(2011).

12. Ajaj, R.M., Saavedra Flores , E.I., Friswell, M.I., Allegri, G., Woods, B.K.S., Isikveren, A.T. and Dettmer, W.G., "The Zigzag wingbox for a span morphing wing", Aerospace Science and Technology, Vol. 28, No. 1, pp. 364-375, (2013).

13. Beaverstock, C.S., Ajaj, R.M., Friswell, M.I., De Breuker, R. and Werter, N.P.M., "Optimizing Mission Performance for a Morphing MAV", Ankara International Aerospace Conference, METU, Ankara Turkey, 11-13 September (2013).

14. Zi-Wu, G. and Yong-Liang, Y., "Study on Aerodynamics and Mechanisms of Elementary Morphing Models for Flapping Wing in Bat Forward Flight", Journal of Arshiv preprint, Arshiv:1403.6824,Journal of Physics and Fluid Dynamics,27 May (2014) .

15. Gopalarathnam, A., Ramasubramanian, M.K. and Wu, F., "Innovative Revolutionary Airspace Designs Advanced Aircraft Wing Concept with Micro- and Macro-Morphing Capability", Department of Mechanical and Aerospace Engineering, North Carolina State University Students supported: Jeffrey Jepson and Qifu Li, 16 May (2003).

16. Li, M., Chen, W.M., Guan, D. and Li, W., "Experimental Validation of Improving Aircraft Rolling Power Using Piezoelectric Actuators", Chinese Journal of Aeronautics, Vol. 18, No. 2, May (2005).

17. Stanford, B., Ifju, P., Albertani, R. and Shyy, W., "Fixed membrane wings for micro air vehicles: Experimental characterization, numerical modeling, and tailoring", Progress in Aerospace Sciences , Vol. 44, No. 4, pp. 258–294, (2008).

18. Bagassi, S., Francia, D. and Persiani, F., "Preliminary Study of a New UAV Concept: The Variable Geometry Vehicle", 27th International Congress of the Aeronautical Sciences,Nice France,19-24 September (2010).

19. Circiu, I. and Prisacariu, V., "Command and Control of the Flying Wing in the Morphing Concept", Review of the Air Force Academy, Vol. 11, No. 1(23), (2013).

20. Probst, T.A., David, B. and Kochersberger, K., "Design and Flight Test of a Morphing UAV Flight Control System", 51st AIAA Aerospace Sciences Meeting including the New Horizons Forum and Aerospace Exposition, Grapevine (Dallas/ft. Worth region),Texas,7-10 January (2013).

21. Tropea, C., yarin, A.L. and Foss, J.F., "Springer handbook of experimental fluid mechanics", Vol. 1, pp. 1047-1060, (2007).

22. Utsunomiya, H., Nagao, F., Ueno, Y. and Noda, M., "Basic study of blockage effects on bluff bodies", Journal of Wind Engineering and Industrial Aerodynamics, Vol. 49, No. 1, pp. 247-256, (1993).

23. Turki, S., Abbassi, H. and Nasrallah, S.B.," Effect of the blockage ratio on the flow in a channel with a built-in square cylinder", Computational Mechanics, Vol. 33, No. 1, pp. 22-29, (2003).

24. Kuchemann, D., "The Aerodynamic Design of Aircraft", Progress in aeronautical sciences, Pergamon, London, (1978).

25. Sadraey, M., "Aircraft Design: A Systems Engineering Approach", John Wiley & Sons, Vol. 71, (2012).

26. Anderson, J.D., "Aircraft Performance and Design", McGraw-Hill, New York, pp. 199-314, (1999).

27. Henry, G.G.,"Roll Control for UAVs by Use of a Variable Span Morphing Wing", Thesis Master of Science, University of Maryland, pp. 24-30, (2005).