Numerical Study of Wheat Conveying in Separator Cyclone using Computational Fluid Dynamics

ماشین های کشاورزی

Article 8, Volume 11, Issue 2 - Serial Number 22, 2021, Pages 231-246   

Document Type: Research Article

DOI: 10.22067/jam.v11i2.79613

Authors

S. Naimei Dizajyekan¹; Gh. Shahgholi^{* 1}; A. Rezvanivand fanaei²; V. Rostampour²

¹Biosystems Engineering Department, Faculty of Agriculture, University of Mohaghegh Ardabili, Ardabil, Iran

²Biosystems Engineering Department, Faculty of Agriculture, Urmia University, Urmia, Iran

Abstract

Introduction
Cyclones are widely used to separate solid particles from the fluid phase. Due to the ease of construction, low running costs, and hard-working conditions at high temperatures, people's interest in using cyclones is increasing day by day. Engineers are generally interested in two parameters to perform a complete evaluation of the design and operation of a cyclone. These parameters are the particle collecting efficiency and the pressure drop inside the cyclone. The precise prediction of the pressure drop in cyclone is very important which it is directly related to operating costs.
Computational Fluid Dynamics (CFD) is a diversified tool for predicting flow behavior in a wide range of design and operational conditions. Numerical solution of Navier-Stokes equations is the basis of all CFD techniques, which is the result of fast computer upgrades and a better understanding of the numerical resolution of turbulence.
Materials and Methods
Regarding preliminary experimental tests and understanding the fluid flow, the flow rate of 0.08 kg s^-1 was selected as the flow rate. Six levels of inlet velocities 10, 12, 14, 16, 18, and 20 m s^-1 were selected for understanding the effect of inlet velocity on the cyclone performance. The measurements were carried out using a hot-air anemometer (TSI-8484model with a resolution of 0.07 m s^-1 and an operating range of 0.125 to 50 m s^-1), and a pressure differential meter instrument (CPE310s-KIMO model) with an accuracy of 0.1 Pa.
The region is discretized as a finite volume in a set, called the region grid or mesh after discretization. For incompressible fluids, pressure-based and density-based solvers are used, respectively. Regarding the velocity of the material entering the cyclone and low Mach number, a pressure-based solver could be used in this study.
The shear stress transport model (SST) is a modified version of the k-ω 2-equation model. This model combines the two turbulence k-ω and k-ε models. The Lagrangian discrete phase model in Ansys Fluent follows to the Euler-Lagrangian model.
Defining the best type of boundary condition is important for solving the problem and extracting solving fields. The boundary conditions used in this study include the inlet velocity in the entrance of cyclone and output pressure in both the upper and lower output sections.
Results and Discussion
In the results section, the results are initially validated by experimental results. Then, the parameters relating to separation efficiency and pressure drop are discussed. Finally, the tangential and axial velocities are considered as important parameters in the cyclone performance.
One of the important issues in the cyclones is the static pressure because it completely affects the phenomenon of separation in the cyclone. The velocities of 16 m s^-1 and 18 m s^-1 have a good potential for use as the base velocity of the inlet fluid to the cyclone. The velocity of 20 m s^-1 is not suitable for separation due to high-pressure drop related to high static pressure.
The separation efficiency in the cyclone was 92 to 99% at all levels, the highest separation efficiency of 99% occurred at the velocity of 16 m s^-1 and the lowest separation efficiency of 9% happened at the velocity of 20 m s^-1.
An increasing trend in axial and radial velocities occurred and the highest tangential velocity occurring in the input section. Considering the working conditions, the inlet velocities of 10 m s^-1 to 16 m s^-1 are appropriate for the turbulence intensity viewpoint.
Conclusion
(1): The speeds 16 m s^-1 and 18 m s^-1 showed a good potential for use as a base velocity of the fluid to the cyclone.
(2): The highest separation efficiency for the velocity of 16 m s^-1 (99%) and lower isolation efficiency was obtained at velocity of 20 m s^-1 (92%).
(3): The velocities of 10 m s^-1 to 16 m s^-1 are suitable input rates from the point of view of turbulence intensity.
(4): It is concluded that from the point of view of wear to the velocity of 10 to 16 m s^-1, practical use is possible, and the velocity of 18 m s^-1 and 20 m s^-1 require the reinforcement of the relevant sections.

Keywords

Cyclone; computational fluid dynamics; Pressure drop; Stairmand

References

1. Hoffmann, A. C., M. De Groot, W. Peng, H. W. A. Dries, and J. Kater. 2001. Advantages and risks in increasing cyclone separator length, American Institute of Chemical Engineers Journal 47: 2452-2460.

2. Alahmadi, Y. H., A. F. Nowakowski. 2016. Modified shear stress transport model with curvature correction for the prediction of swirling flow in a cyclone separator, Chemical Engineering Science 147: 150-165.

3. Alexander, R. M. 1949. Fundamentals of cyclone design and operation, Australasian Institute of Mining and Metallurgy 152: 152-153.

4. Elsayed, K., and C. Lacor. 2010. Optimization of the cyclone separator geometry for minimum pressure drop using mathematical models and CFD simulations. Chemical Engineering Science 65: 6048-6058.

5. Gimbun, J., T. G. Chuah, A. Fakhru’l-Razi, and T. S. Y. Choong. 2005b. The influence of temperature and inlet velocity on cyclone pressure drop: a CFD study.Chemical Engineering and Processing 44: 7-12.

6. Gimbun, J., T. G. Chuah, T. S. Y. Choong, and A. Fakhru’l-Razi. 2005a. A CFD study on the prediction of cyclone collection efficiency. International Journal for Computational Methods in Engineering Science and Mechanics 6: 161-168.

7. Gimbun, J., T. G. Chuah, T. S. Y. Choong, and A. Fakhru’l-Razi. 2005c. Prediction of the effects of cone tip diameter on the cyclone performance, Journal of Aerosol Science 1056-1065.

8. Griffiths, W. D., and F. Boysan. 1996. Computational fluid dynamics (CFD) and empirical modelling of the performance of a number of cyclone samplers. Journal of Aerosol Science 27: 281- 304.

9. Hoekstra, A. J., J. J. Derksen, and H. E. A. Van Den Akker. 1999. An experimental and numerical

study of turbulent swirling flow in gas cyclones, Chemical Engineering Science 54: 2055-2065.

10. Inc. ANSYS. 2013. ANSYS FLUENT Theory Guide. Release 182 15317: 373-464.

11. Naddi, F., S. A, Mehdizadeh, U. N. Zonuz. 2017. Comparing between predicted output temperature of flat-plate solar collector and experimental results: computational fluid dynamics and artificial neural network: Journal of Agricultural Machinery 7 (1): 298-311. (In Farsi).

12. Rezvanivandefanayi, A., and A. M. Nikbakht. 2015. A CFD Study of the Effects of Feed Diameter on the Pressure Drop in Acyclone Separator: International Journal of Food Engineering 11: 71-77.

13. Rezvanivandefanayi, A., A. Hasanpour, and A. M. Nikbakht. 2019. Study of the vapor thermos-compressor to reduce energy consumption in the sugar production line using Computational Fluid Dynamics: Journal of Agricultural Machinery 10 (2). (In Farsi).

14. Rezvanivandefanayi, A., A. M. Nikbakht, and A. Modarres Motlagh. 2013a. Modeling of material conveying in cyclone separators using Computational fluid Dynamics: The 6th Agricultural Research Findings Conference. University of Kurdistan, Sanandaj, Iran.

15. Rezvanivandefanayi, A., A. M. Nikbakht, and A. Modarres Motlagh. 2013b. Investigating the effect of mass flow rate on velocity fields of cyclone separators using computational fluid dynamics: The second national congress of organic and conventional agriculture, University of Mohaghegh Ardabili, Ardabil, Iran.

16. Rezvanivandefanayi, A., A. M. Nikbakht, and A. Modarres Motlagh. 2013c. Investigating the effect of mass flow rate on the friction of the wall of cyclone separators using computational fluid dynamics: The second national congress of organic and conventional agriculture, University of Mohaghegh Ardabili, Ardabil, Iran.

17. Rezvanivandefanayi, A., A. M. Nikbakht, and A. Modarres Motlagh. 2013d. Investigating the effect of mass flow rate on Pressure drop of cyclone separators using computational fluid dynamics: The second national congress of organic and conventional agriculture, University of Mohaghegh Ardabili, Ardabil, Iran.

18. Zhao, B., Y. Su, and J. Zhang. 2006. Simulation of gas flow pattern and separation efficiency in cyclone with conventional single and spiral double inlet configuration. Chemical Engineering Research and Design 84: 1158-1165.