Effect of Tidal conditions, Supplementary Cementitious Materials and Marine's Materials on Some of Concrete Durability Parameters

مهندسی عمران فردوسی

Article 5, Volume 36, Issue 3 - Serial Number 43, September 2023, Pages 63-82   

Document Type: Original Article

DOI: 10.22067/jfcei.2023.83067.1239

Authors

Mohammad Jahani^{* 1}; Shore Shahnoori²; Saeed Moradi³; Mohammad Yazdani⁴; Cyrus Ershadi⁵

¹Marine Structures, University of Hormozgan, Bandar Abbas, Iran.

²Built Environment, Smart Architectural Technologies, Eindhoven University of Technology, Netherlands

³Urban Development Research Center (BHRC), Persian Gulf Branch,, Bandar Abbas, IRAN.

⁴Marine structures, University of Hormozgan, Iran

⁵Department of Civil Engineering, Faculty of Technical Engineering, University of Hormozgan, Bandar Abbas, Iran

Abstract

The use of dredged-marine-sand and seawater for concrete production is practically more justified in marine environments due to the primary sources of these materials. Also, it is very crucial to examine the durability parameters of concrete structures in marine environments, especially in tidal conditions, because in these area, consecutive dry/wet cycles, temperature and humidity gradients over time, intensify carbonation and diffusion of conductive ions, therefore physical and chemical deterioration accelerated accordingly. The aim of this research is to investigate the effect of metakaolin, silica fume, and slag on the mechanical properties and microstructure Seawater-seasand concrete in tidal conditions. The results showed that the use of seawater and sand in concrete, due to the presence of chloride ions as well as the filling of voids by ettringite caused by the sulfates attacks, led to the improvement of mechanical properties in the early ages, but after that, a significant drop was occurred. Due to the high source of SiO2 and its high reactivity, silica fume accelerated the consumption of calcium hydroxide, prevented carbonation progress, and formed a dense calcium-silicate-hydrate gel in the microstructure of Seawater-seasand-concrete, and in the presence of magnesium sulfate, better than slag and metakaolin, prevented the formation of ettringite and therefore, propagation of pores and microcracks.

Keywords

Durability of concrete; Mechanical properties; Concrete microstructure; Dredged marine sand; Tidal conditions

References

[1] M. Khatibmasjedi, S. Ramanathan, P. Suraneni, and A. Nanni, “Compressive strength development of seawater-mixed concrete subject to different curing regimes,” ACI Mater. J., vol. 117, no. 5, 2020. doi: 10.14359/51725973.

[2] U. Ebead, D. Lau, F. Lollini, A. Nanni, P. Suraneni, and T. Yu, “A review of recent advances in the science and technology of seawater-mixed concrete,” Cement and Concrete Research, vol. 152, p. 106666, 2022. https://doi.org/10.1016/j.cemconres.2021.106666

[3] M. Jahani, S. Shahnoori, S. Moradi, and C. Ershadi, “Cleaner Production Towards a Green Concrete ; Multi-scale Experimental Study on Long-Term Performance of a Sustainable Modified-SWSSC,” vol. 6, no. 6, pp. 43–59, 2022. https://doi.org/10.11648/j.ajcbm.20220601.14

[4] S. Moradi, S. Shahnoori, S. T. Tabatabaei Aghda, and C. Ershadi, “Study of resistance and durability parameters of Roller Compacted Concrete Pavement made of Dredged Marine Sand extracted from the coastal areas of Persian Gulf (Shahid Rajaee port),” Concr. Res., vol. 11, no. 3, pp. 41–53, 2018. (In Persian). https://doi.org/10.22124/jcr.2018.7437.1239

[5] S. Moradi, and S. Shahnoori, “Eco-friendly mix for Roller-Compacted Concrete: Effects of Persian-Gulf-Dredged marine sand on durability and resistance parameters of concrete,” Construction and building Materials, vol. 281, pp. 122555, 2021. https://doi.org/10.1016/j.conbuildmat.2021.122555.

[6] A. Shayan, A. Xu, G. Chirgwin, and H. Morris, “Effects of seawater on AAR expansion of concrete,” Cement Concrete Research, vol. 40, no. 4, pp. 563-568, 2010. https://doi.org/10.1016/j.cemconres.2009.09.008

[7] H. H. Steinour, “Concrete Mix Water--How Impure Can It Be?,” 1960.

[8] M. Jahani, S. Shahnoori, and S. Moradi, “Long Term observations in an Experimental study on durability of a Sustainable Concrete Made with Sea-water and Sea-sand in Tidal Conditions,” 2022.

[9] M. Khatibmasjedi, S. Ramanthan, P. Suraneni, and A. Nanni, “Shrinkage behavior of cementitious mortars mixed with seawater,” Adv. Civ. Eng. Mater., vol. 8, no. 2, pp. 64–78, 2019. https://doi.org/10.1520/ACEM20180110

[10] A. M. Rashad, and A. S. Ouda, “Effect of tidal zone and seawater attack on high-volume fly ash pastes enhanced with metakaolin and quartz powder in the marine environment,” Microporous and Mesoporous Materials, vol. 324, pp. 111261, 2021. https://doi.org/10.1016/j.micromeso.2021.111261

[11] X. Shen, Q. F. Liu, Z. Hu, W. Q. Jiang, X. Lin, D. Hou, and P. Hao, “Combine ingress of chloride and carbonation in marine-exposed concrete under unsaturated environment: A numerical study,” Ocean Engineering, vol. 189, pp. 106350, 2019. https://doi.org/10.1016/j.oceaneng.2019.106350

[12] Y. Yi, D. Zhu, S. Guo, Z. Zhang, and C. Shi, “A review on the deterioration and approaches to enhance the durability of concrete in the marine environment,” Cement Concrete Composites, vol. 113, pp. 103695, 2020. https://doi.org/10.1016/j.cemconcomp.2020.103695

[13] X. Jiang, S. Mu, Z. Yang, J. Tang, and T. Li, “Effect of temperature on durability of cement-based material to physical sulfate attack,” Construction and Building Materials, vol. 266, pp. 120936, 2021. https://doi.org/10.1016/j.conbuildmat.2020.120936

[14] J. Liu, G. Ou, Q. Qiu, X. Chen, J. Hong, and F. Xing, “Chloride transport and microstructure of concrete with/without fly ash under atmospheric chloride condition,” Construction and Building Materials, vol. 146, pp. 493–501, 2017. https://doi.org/10.1016/j.conbuildmat.2017.04.018

[15] R. M. De Gutiérrez, L. N. Diaz, and S. Delvasto, “Effect of pozzolans on the performance of fiber-reinforced mortars,” Cement Concrete Composites, vol. 27, no. 5, pp. 593–598, 2005. https://doi.org/10.1016/j.cemconcomp.2004.09.010

[16] S. Cheng, Z. Shui, T. Sun, Y. Huang, and K. Liu, “Effects of seawater and supplementary cementitious materials on the durability and microstructure of lightweight aggregate concrete,” Construction and building Materials, vol. 190, pp. 1081–1090, 2018. https://doi.org/10.1016/j.conbuildmat.2018.09.178

[17] D. L. Pillay, O. B. Olalusi, M. W. Kiliswa, P. O. Awoyera, J. T. Kolawole, and A. J. Babafemi, “Engineering performance of metakaolin based concrete,” Cleaner Engineering and Technology, vol. 6, p. 100383, 2022. https://doi.org/10.1016/j.clet.2021.100383

[18] M. Valipour, F. Pargar, M. Shekarchi, and S. Khani, “Comparing a natural pozzolan, zeolite, to metakaolin and silica fume in terms of their effect on the durability characteristics of concrete: A laboratory study,” Construction and building Materials, vol. 41, pp. 879–888, 2013. https://doi.org/10.1016/j.conbuildmat.2012.11.054

[19] W. A. Al-Kutti and N. M. Al-Akhras, “The durability of partially-damaged concrete with the addition of silica fume and ground granulated blast furnace slag,” Key Engineering Materials, vol. 711, pp. 277–284, 2016. https://doi.org/10.4028/www.scientific.net/KEM.711.277

[20] Jahani, A., Estabragh, A. R., Khajepour, H., & Amini, M. (2022). Comparison of the Effect of Cement, Ground Granulated Blast-Furnace Slag (GGBS), and Activated GGBS on Stabilization of a Clay Soil. Ferdowsi Civil Engineering, vol.35, no.3. doi:10.22067/jfcei.2022.74908.1115

[21] A. R. Estabragh, A. Jahani, A. A. Javadi, and M. Babalar, “Assessment of different agents for stabilisation of a clay soil,” International Journal of Pavement Engineering, vol. 23, no. 2, 2022. https://doi.org/10.1080/10298436.2020.1736293

[22] ASTM Committee, “Standard Test Method for Total Evaporable Moisture Content of Aggregate by Drying, ASTM C566-97,” Annu. B. ASTM Stand., vol. 97, no. Reapproved 2004, pp. 5–7, 1997.

[23] C128/C128M, “Standard Test Method for Density, Relative Density (Specific Gravity), and Absorption,” ASTM International, pp. 1–6, 2001.

[24] ASTM C143/C143M, “Standard Test Method for Slump of Hydraulic-Cement Concrete,” Astm C143, no. 1, pp. 1–4, 2015.

[25] Z. Shi, Z. Shui, Q. Li, and H. Geng, “Combined effect of metakaolin and sea water on performance and microstructures of concrete,” Construction and building Materials, vol. 74, pp. 57-64, 2015. https://doi.org/10.1016/j.conbuildmat.2014.10.023

[26] “Bs 1881 Part 124 Pdf 14l 1 / 3,” pp. 3–5, 1881.

[27] ACI Committee 222, “Protection of Metals in Concrete Against Corrosion,” Aci 222R-01, pp. 1–41, 2001.

[28] Limeira, J., Etxeberria, M., Agulló, L., & Molina, D. (2011). Mechanical and durability properties of concrete made with dredged marine sand. Construction and building materials, 25(11), 4165-4174. https://doi.org/10.1016/j.conbuildmat.2011.04.053

[29] O. Cascudo, P. Pires, H. Carasek, A. De Castro, and A. Lopes, “Evaluation of the pore solution of concretes with mineral additions subjected to 14 years of natural carbonation,” Cement Concrete Composites, vol. 115, pp. 103858, 2021. https://doi.org/10.1016/j.cemconcomp.2020.103858

[30] A. Younis, U. Ebead, P. Suraneni, and A. Nanni, “Fresh and hardened properties of seawater-mixed concrete,” Construction and building Materials, vol. 190, pp. 276–286, 2018. https://doi.org/10.1016/j.conbuildmat.2018.09.126

[31] P. Sikora, K. Cendrowski, M. Abd Elrahman, S. Y. Chung, E. Mijowska, and D. Stephan, “The effects of seawater on the hydration, microstructure and strength development of Portland cement pastes incorporating colloidal silica,” Applied Nanoscience, vol. 10, no. 8, pp. 2627-2638, 2020. https://doi.org/10.1007/s13204-019-00993-8

[32] Y. Demir, H. Yaprak, and O. ŞİMŞEK, “The effect of sea water on the properties of concrete with silica fume admixture,” Cem. Wapno Bet., vol. 15, no. 1, 2010.

[33] M. Williams, J. M. Ortega, I. Sánchez, M. Cabeza, and M. Á. Climent, “Non-destructive study of the microstructural effects of sodium and magnesium sulphate attack on mortars containing silica fume using impedance spectroscopy,” Applied Science, vol. 7, no. 7, p. 648, 2017. https://doi.org/10.3390/app7070648

[34] H. W. Song, S. W. Pack, S. H. Nam, J. C. Jang, and V. Saraswathy, “Estimation of the permeability of silica fume cement concrete,” Construction and building Materials, vol. 24, no. 3, pp. 315–321, 2010. https://doi.org/10.1016/j.conbuildmat.2009.08.033

[35] M. R. Akram, and S. Raza, “Effect of micro silica and ggbs on compressive strength and permeability of impervious concrete as a cement replacement,” Eur. Acad. Res., vol. 3, no. 7, pp. 7456–7468, 2015.

[36] S. A. Barbhuiya, P. A. M. Basheer, M. W. Clark, and G. I. B. Rankin, “Effects of seawater-neutralised bauxite refinery residue on properties of concrete,” Cement Concrete Composites, vol. 33, no. 6, pp. 668–679, 2011. https://doi.org/10.1016/j.cemconcomp.2011.03.010

[37] S. Sadati, M. K. Moradllo, and M. Shekarchi, “Long-term durability of onshore coated concrete—chloride ion and carbonation effects,” Frontiers of Structural and Civil Engineering, vol. 10, no. 2, pp. 150–161, 2016. https://doi.org/10.1007/s11709-016-0341-2

[38] H. Li, N. Farzadnia, and C. Shi, “The role of seawater in interaction of slag and silica fume with cement in low water-to-binder ratio pastes at the early age of hydration,” Construction and building Materials, vol. 185, pp. 508-518, 2018. https://doi.org/10.1016/j.conbuildmat.2018.07.091

[39] M. Guo, B. Hu, F. Xing, X. Zhou, M. Sun, L. Sui, and Y. Zhou, “Characterization of the mechanical properties of eco-friendly concrete made with untreated sea sand and seawater based on statistical analysis,” Construction and building Materials, vol. 234, pp. 117339, 2020. https://doi.org/10.1016/j.conbuildmat.2019.117339

[40] M. Jahani, S. Moradi, S. Shahnoori, “4-year monitoring of degradation mechanisms of seawater sea-sand concrete exposed to tidal conditions: development of chemical composition and micro-performance,” Constr. Build. Mater., vol. 409, pp. 133475, 2023. https://doi.org/10.1016/j.conbuildmat.2023.133475