Production of aerated chocolate and application of X-ray computed tomography and image processing in evaluating the bubbles features

مجله پژوهشهای علوم و صنایع غذایی ایران

Article 2, Volume 16, Issue 5 - Serial Number 65, November and December 2020, Pages 525-540   

Document Type: Research Article

DOI: 10.22067/ifstrj.v16i5.83979

Authors

Messiah Sarfarazi¹; Mohebbat Mohebbi^{* 1}; Mahdi Saadatmand-Tarzjan²; Ali Mirshahi³

¹Department of Food Science and Technology, Faculty of Agriculture, Ferdowsi University of Mashhad, Mashhad, Iran.

²Department of Electrical Engineering, Faculty of Engineering, , Ferdowsi University of Mashhad, Mashhad, Iran.

³Department of Clinical Sciences, Faculty of Veterinary Medicine, Ferdowsi University of Mashhad, Mashhad, Iran.

Abstract

Introduction: Chocolate is a suspension of solid particles, including sugar, cocoa solids and milk powder (depending on the chocolate type) in a continuous fat phase, namely cocoa butter or its substitutes. The solid particles account for approximately 70% of chocolate with the fat constituting about 30%. Sugar takes up nearly 40–50% of the total solid particles of chocolate, thus influencing its sweetness, particle size distribution, rheological and sensory properties. It is also considered to be a bulking agent and a source of energy which produces 394 kcal/100 g of refined sugar. Therefore, consumers are increasingly becoming concerned with chocolate sugar and calorie content nowadays. This issue can be resolved by replacing sugar with bulk (nutritive) sweeteners and/or dietary fibers. Bubbles are found in many food products, including cakes, chocolates and beverages. Although they do not increase the food nutritional value, they change its textural properties and mouthfeel. Bubbles are normally visible to the naked eye and their mean diameter ranges from 0.05 to 3 mm. X-ray computed tomography is a 3D imaging technique which captures the images of a sample cross-sections. It is used for the non-destructive visualization and characterization of food microstructure. In this method, a series of radiographs of a sample are captured from different angles to be utilized for the 3D reconstruction of the material microstructure.
 
Materials and methods: sugar was replaced with inulin: maltodextrin mixture at ratios of 25:75 (CH2), 50:50 (CH3) and 75:25 (CH4). Carbon dioxide was injected into the samples at 6 bar to produce aerated chocolate. Using X-ray computed tomography, the images of the samples were captured and after processing, the obtained images were segmented using the Chan-Vese method. The properties of bubbles included total volume, diameter and surface to volume ratio. The crystallinity of the samples was determined through X-ray diffraction. The hardness of the chocolate bars was measured using the puncture test. The density of the aerated chocolates was also compared with that of the nonaerated ones.
 
Introduction: Chocolate is a suspension of solid particles, including sugar, cocoa solids and milk powder (depending on the chocolate type) in a continuous fat phase, namely cocoa butter or its substitutes. The solid particles account for approximately 70% of chocolate with the fat constituting about 30%. Sugar takes up nearly 40–50% of the total solid particles of chocolate, thus influencing its sweetness, particle size distribution, rheological and sensory properties. It is also considered to be a bulking agent and a source of energy which produces 394 kcal/100 g of refined sugar. Therefore, consumers are increasingly becoming concerned with chocolate sugar and calorie content nowadays. This issue can be resolved by replacing sugar with bulk (nutritive) sweeteners and/or dietary fibers. Bubbles are found in many food products, including cakes, chocolates and beverages. Although they do not increase the food nutritional value, they change its textural properties and mouthfeel. Bubbles are normally visible to the naked eye and their mean diameter ranges from 0.05 to 3 mm. X-ray computed tomography is a 3D imaging technique which captures the images of a sample cross-sections. It is used for the non-destructive visualization and characterization of food microstructure. In this method, a series of radiographs of a sample are captured from different angles to be utilized for the 3D reconstruction of the material microstructure.
 
Materials and methods: sugar was replaced with inulin: maltodextrin mixture at ratios of 25:75 (CH2), 50:50 (CH3) and 75:25 (CH4). Carbon dioxide was injected into the samples at 6 bar to produce aerated chocolate. Using X-ray computed tomography, the images of the samples were captured and after processing, the obtained images were segmented using the Chan-Vese method. The properties of bubbles included total volume, diameter and surface to volume ratio. The crystallinity of the samples was determined through X-ray diffraction. The hardness of the chocolate bars was measured using the puncture test. The density of the aerated chocolates was also compared with that of the nonaerated ones.
 
Results and discussion: X-ray diffraction revealed that there were many strong peaks in the diffractogram of CH1, which can be ascribed to the high degree of sugar crystallinity in addition to the impurities present in the commercial sugar utilized in this study. In the case of the sugar-free samples, namely CH2, CH3 and CH4, two distinct peaks could be seen at 2θ of about 21° and 23.5°, both of which were much stronger and more defined in the scattering pattern of CH3, demonstrating the more crystalline structure of this sample. It seems that inulin and maltodextrin have physically interacted with each other or with the other ingredients of the chocolate, in particular CBS, which has been more pronounced at the ratio of 50:50. The results of image segmentation showed that the Chan-Vese method, compared with the adaptive thresholding one, was more able to segment the images, because this method does not depend on the image gradient and is especially suitable for the objects with vague edges. The mean bubble diameter of CH1 was bigger than that of the other samples, which could be due to its higher degree of crystallinity, because the crystalline structure of CH1 prevented the gas from being lost leading to the coalescence of smaller bubbles and the formation of bigger ones. In addition, it was observed that the density of the aerated chocolate was higher than that of the unaerated one in all the formulas as a portion of solid particles and fat was replaced with the gas. The results also demonstrated that the sugar-free aerated samples were softer than the corresponding nonaerated ones. However, it was reversed in the case of CH1 which could be ascribed to the presence of sugar in this sample, because in aerated products, solid particles, particularly sugar, form a continuous skeleton and play the same role as fat does in nonaerated products.

Keywords

Inulin; Maltodextrin; X-ray computed tomography; X-ray diffraction; Chan-Vese; Hardness

References

Afoakwa, E. O., Paterson, A., & Fowler, M. (2007). Factors influencing rheological and textural qualities in chocolate–a review. Trends in Food Science & Technology, 18(6), 290-298.

Aidoo, R. (2015). Functionality of inulin and polydextrose in stevia or thaumatin sweetened dark chocolate. (PhD thesis), Ghent University, Belgium.

Aidoo, R. P., Afoakwa, E. O., & Dewettinck, K. (2014). Optimization of inulin and polydextrose mixtures as sucrose replacers during sugar-free chocolate manufacture–Rheological, microstructure and physical quality characteristics. Journal of Food Engineering, 126, 35-42.

Aidoo, R. P., Appah, E., Van Dewalle, D., Afoakwa, E. O., & Dewettinck, K. (2017). Functionality of inulin and polydextrose as sucrose replacers in sugar‐free dark chocolate manufacture–effect of fat content and bulk mixture concentration on rheological, mechanical and melting properties. International Journal of Food Science & Technology, 52(1), 282-290.

Aidoo, R. P., Depypere, F., Afoakwa, E. O., & Dewettinck, K. (2013). Industrial manufacture of sugar-free chocolates–applicability of alternative sweeteners and carbohydrate polymers as raw materials in product development. Trends in Food Science & Technology, 32(2), 84-96.

Bellido, G. G., Scanlon, M. G., Page, J. H., & Hallgrimsson, B. (2006). The bubble size distribution in wheat flour dough. Food Research International, 39(10), 1058-1066.

Belščak-Cvitanović, A., Komes, D., Dujmović, M., Karlović, S., Biškić, M., Brnčić, M., & Ježek, D. (2015). Physical, bioactive and sensory quality parameters of reduced sugar chocolates formulated with natural sweeteners as sucrose alternatives. Food Chemistry, 167, 61-70.

Bitaraf, S., Abbasi, S., & HAMIDI, E. Z. (2016). Effects of inulin and bulking agents on rheological properties and particle size distribution of low calorie dark chocolate.

Bitaraf, S., Abbasi, S., & Hamidi, Z. (2013). Production of low-energy prebiotic dark chocolate using inulin, polydextrose, and maltodextrin. Iranian Journal of Nutrition Sciences & Food Technology, 8(1), 49-62.

Bradley, D., & Roth, G. (2007). Adaptive thresholding using the integral image. Journal of graphics tools, 12(2), 13-21.

Campbell, G. M., & Mougeot, E. (1999). Creation and characterisation of aerated food products. Trends in Food Science & Technology, 10(9), 283-296.

Chan, T. F., & Vese, L. A. (2001). Active contours without edges. IEEE Transactions on image processing, 10(2), 266-277.

Chiotellis, E., & Campbell, G. M. (2003). Proving of bread dough I: modelling the evolution of the bubble size distribution. Food and Bioproducts Processing, 81(3), 194-206.

Erdem, Ö., Gültekin-Özgüven, M., Berktaş, I., Erşan, S., Tuna, H. E., Karadağ, A., . . . Cutting, S. M. (2014). Development of a novel synbiotic dark chocolate enriched with Bacillus indicus HU36, maltodextrin and lemon fiber: Optimization by response surface methodology. LWT-Food Science and Technology, 56(1), 187-193.

Falcone, P., Baiano, A., Zanini, F., Mancini, L., Tromba, G., Montanari, F., & Del Nobile, M. (2004). A novel approach to the study of bread porous structure: phase-contrast X-ray microtomography. JOURNAL OF FOOD SCIENCE-CHICAGO-, 69(1), FEP38-FEP38.

Farzanmehr, H., & Abbasi, S. (2009). Effects of inulin and bulking agents on some physicochemical, textural and sensory properties of milk chocolate. Journal of texture studies, 40(5), 536-553.

Furlan, L. T. R., Baracco, Y., Lecot, J., Zaritzky, N., & Campderros, M. E. (2017). Influence of hydrogenated oil as cocoa butter replacers in the development of sugar-free compound chocolates: Use of inulin as stabilizing agent. Food Chemistry, 217, 637-647.

Glicerina, V., Balestra, F., Dalla Rosa, M., & Romani, S. (2013). Rheological, textural and calorimetric modifications of dark chocolate during process. Journal of Food Engineering, 119(1), 173-179.

Granato, D., de Araújo Calado, V. M., & Jarvis, B. (2014). Observations on the use of statistical methods in Food Science and Technology. Food Research International, 55(0), 137-149. doi:http://dx.doi.org/10.1016/j.foodres.2013.10.024

Haedelt, J. (2005). An investigation into bubble inclusion into liquid chocolate. The University of Reading.

Haedelt, J., Beckett, S., & Niranjan, K. (2007). Bubble‐Included Chocolate: Relating Structure with Sensory Response. Journal of Food Science, 72(3), E138-E142.

Haedelt, J., Pyle, D. L., Beckett, S. T., & Niranjan, K. (2005). Vacuum‐induced Bubble Formation in Liquid‐tempered Chocolate. Journal of Food Science, 70(2), E159-E164.

Konar, N., Özhan, B., Artık, N., Dalabasmaz, S., & Poyrazoglu, E. S. (2014). Rheological and physical properties of inulin-containing milk chocolate prepared at different process conditions. CyTA-Journal of Food, 12(1), 55-64.

Konar, N., Palabiyik, İ., Toker, O. S., Polat, D. G., Sener, S., Akcicek, A., & Sagdic, O. (2017). Effect of Inulin DP on Various Properties of Sugar-Free Dark Chocolates Containing Lactobacillus paracasei and Lactobacillus acidophilus. International Journal of Food Engineering, 13(9).

Massey, A., Khare, A., & Niranjan, K. (2001). Air inclusion into a model cake batter using a pressure whisk: development of gas hold‐up and bubble size distribution. Journal of Food Science, 66(8), 1152-1157.

Misra, N., Phalak, R., & Martynenko, A. (2018). A microscopic computer vision algorithm for autonomous bubble detection in aerated complex liquids. Journal of Food Engineering, 238, 54-60.

Niranjan, K., & Silva, S. (2008). Bubble-containing foods Food Materials Science (pp. 281-303): Springer.

Pandey, A., & Singh, G. (2011). Development and storage study of reduced sugar soy containing compound chocolate. Journal of food science and technology, 48(1), 76-82.

Peters, D. J. (2017). Non‐conventional machines and processes. Beckett's Industrial Chocolate Manufacture and Use, 400-430.

Rezende, N. V., Benassi, M. T., Vissotto, F. Z., Augusto, P. P., & Grossmann, M. V. (2015). Mixture design applied for the partial replacement of fat with fibre in sucrose-free chocolates. LWT-Food Science and Technology, 62(1), 598-604.

Shah, A. B., Jones, G. P., & Vasiljevic, T. (2010). Sucrose‐free chocolate sweetened with Stevia rebaudiana extract and containing different bulking agents–effects on physicochemical and sensory properties. International Journal of Food Science & Technology, 45(7), 1426-1435.

Shoaib, M., Shehzad, A., Omar, M., Rakha, A., Raza, H., Sharif, H. R., . . . Niazi, S. (2016). Inulin: Properties, health benefits and food applications. Carbohydrate Polymers, 147, 444-454.

Shourideh, M., Taslimi, A., Azizi, M., & Mohammadifar, M. (2012). Effects of D-Tagatose and inulin on some physicochemical, rheological and sensory properties of dark chocolate. International Journal of Bioscience, Biochemistry and Bioinformatics, 2(5), 314.

Sokmen, A., & Gunes, G. (2006). Influence of some bulk sweeteners on rheological properties of chocolate. LWT-Food Science and Technology, 39(10), 1053-1058.

Watson, N, Hazlehurst, T, Povey, M, Vieira, J, Sundara, R, & Sandoz, JP. (2014). Can airborne ultrasound monitor bubble size in chocolate? Paper presented at the Journal of Physics: Conference Series.

Winkelmeyer, C. B., Peyronel, F., Weiss, J., & Marangoni, A. G. (2016). Monitoring Tempered Dark Chocolate Using Ultrasonic Spectrometry. Food and Bioprocess Technology, 9(10), 1692-1705. doi:10.1007/s11947-016-1755-5