Investigating the Effect of Storage Time on the Mechanical Properties of Biodegradable Polylactic Acid Film Containing Zinc Oxide Nanoparticles

ماشین های کشاورزی

Volume 14, Issue 3 - Serial Number 33, September 2024, Pages 283-299   

Document Type: Research Article

DOI: 10.22067/jam.2023.81863.1160

Authors

N. Tajari¹; H. Sadrnia^{* 1}; F. Hosseini²

¹Department of Biosystems Engineering, Faculty of Agriculture, Ferdowsi University of Mashhad, Mashhad, Iran

²Department of Food Additives, Iranian Academic Centre for Education Culture and Research (ACECR), Khorasan Razavi, Iran

Abstract

Introduction
Polylactic acid (PLA) is a biodegradable polymer that can replace petroleum-based materials in packaging films due to its unique properties. However, sometimes the degradability of polymers can be considered a negative factor, such as when significant changes in the mechanical properties of the polymer occur during use. Another notable issue is the brittleness of polylactic acid, which can be modified to some extent by adding other materials. The addition of materials such as nanoparticles and plasticizers can improve the flexibility and mechanical properties of polymer films. Polymer films must possess acceptable physical, mechanical, thermal, and other relevant characteristics for use in the packaging industry. The acceptable level of these properties can be obtained by comparing them with the established standards for commonly used polymers in the industry. Low density polyethylene (LDPE) is a polymer widely used in the packaging industry, making it a good benchmark for comparison. This research focused on studying various factors affecting the quality of the produced films, including mechanical properties, light absorption, contact angle, and microstructures. Investigating the mechanical properties of the PLA films is crucial due to the polymer’s degradability over time. Polylactic acid films with different compounds containing PEG 400 and Tween 80 as plasticizers and ZnO nanoparticles were investigated for 14 months (in the first, second, third, fourth, and fourteenth months) in terms of mechanical properties. Finally, the obtained values were compared with standard values for packaging and their mechanical behavior was analyzed.
Materials and Methods
Experiments were performed in the post-harvest and central laboratories of Ferdowsi University of Mashhad, Iran. The films were prepared using the solvent casting method. First, PLA granules were dried for 24 hours at 60 °C and then 1 g of PLA in 50 ml of dichloromethane was dissolved at room temperature by magnetic stirring for 12 hours. ZnO nanoparticles, PEG 400 and Tween 80 were incorporated into PLA and DCM solution, 1 wt% PLA, 20 wt% PLA, and 0.25 wt% solution, respectively. To prepare films containing nanoparticles, nanoparticles and dichloromethane were sonicated with an ultrasonic probe for 10 minutes and then added to the base solution and stirred for one hour.
Mechanical properties of the samples were determined based on the ASTM D882-02 standard method. A texture analyzer (H5 KS, Manchester, U.K.) was used for this test. Light absorption was studied using a spectrophotometer (CAMSPECM550, UK). The contact angle of the samples was measured using a goniometer (model 200-00, Ramé-Hart Instrument Co, Succasunna, USA) in accordance with the ASTM D5946-04 standard. The surface morphology of the samples was visualized using scanning electron microscope (LMU TESCAN BRNO-Mira3, Czech Republic). The results were analyzed using Minitab software version 18 (Minitab Inc, USA) and the graphs were created in Microsoft Excel 2013.
Results and Discussion
The neat PLA film has a smooth surface, and with the addition of nanoparticles or plasticizers, the surfaces become uneven. The addition of nanoparticles and plasticizers caused more opacity of the film and better protection against ultraviolet rays. The presence of plasticizers, especially Tween 80, increased the hydrophilicity of the films. Packaging films should be flexible and have ductile behavior and the addition of plasticizers caused ductile behavior. However, Tween 80 was not able to create stable ductile behavior. The stress-strain diagram shows that most samples displayed ductile behavior over 14 months, except for the neat PLA film and the film containing Tween 80 and nanoparticles. The values of tensile strength, elastic modulus, and elongation at break for low density polyethylene have been reported as 11.7 MPa, 260.4 MPa, and 225%, respectively. The lowest value of tensile strength (18.56 MPa) and elastic modulus (1114.68 MPa) were related to P400/T80 film. This difference shows the acceptability of polylactic acid in the packaging industry. The elongation value is much lower than the standard, indicating the need to modify this parameter.
Conclusion
The research findings revealed a significant effect of film type on mechanical properties, as well as a remarkable impact of storage time on tensile strength and elongation at break. The effect of various factors such as changes in the texture of the film due to the presence of plasticizers or non-uniform distribution of nanoparticles makes it impossible to determine a consistent trend for the effect of time on the films. The elongation at break for the produced films was much lower than the standard, which still needs to be modified due to the importance and sensitivity of this parameter in packaging. Polylactic acid has high tensile strength and high elastic modulus. Therefore, it can be combined with other polymers, various plasticizers, or nanoparticles at higher percentage to improve flexibility. The presence of plasticizers and nanoparticles in the film substrate increased opacity and enhanced protection against ultraviolet rays. The produced films were more hydrophilic compared to low density polyethylene.
Acknowledgment
This research was supported by Ferdowsi University of Mashhad (Grant No. 54096). The authors would like to thank Dr. Mohammadreza Pajohi-Alamoti, Department of Food Hygiene and Quality Control, Bu-Ali Sina University, Hamedan, Iran for providing polylactic acid granules.

Keywords

Elastic modulus; Elongation at break; Mechanical behavior; Packaging film; Tensile strength

References

1. Aktas, C., Polat, O., Beitollahpoor, M., Farzam, M., Pesika, N. S., & Sahiner, N. (2023). Force-Based Characterization of theWetting Properties of LDPE Surfaces Treated with CF₄ and H₂ Polymers, 15(9), 2132. https://doi.org/10.3390/polym15092132
2. Arrieta, M. P., Garrido, L., Faba, S., Guarda, A., Galotto, M. J., & Dicastillo, C. L. D. (2020). Cucumis metuliferus Fruit Extract Loaded Acetate Cellulose Coatings for Antioxidant Active Packaging. Polymers, 12(6), 1248. https://doi.org/10.3390/polym12061248
3. ASTM. (2008). Standard Specification for Polyethylene Films Made from Low-Density Polyethylene for General Use and Packaging Applications (Vol. D4635– 08a). USA.
4. ASTM. (2010). Standard Test Method for Tensile Properties of Thin Plastic Sheeting (Vol. ASTM D882-02). USA.
5. ASTM. (2017). Standard Test Method for Corona-Treated Polymer Films Using Water Contact Angle Measurements (Vol. ASTM D5946-04 ). USA.
6. Avolio, R., Castaldo, R., Avella, M., Cocca, M., Gentile, G., Fiori, S., & Maria, E. E. (2018). PLA-based plasticized nanocomposites: Effect of polymer/plasticizer/filler interactions on the time evolution of properties. Composites Part B, 152, 267-274. https://doi.org/10.1016/j.compositesb.2018.07.011
7. Bijarimi, M., Ahmad, S., Rasid, R., Khushairi, M. A., & Zakir, M. (2016). Poly(lactic acid)/ Poly(ethylene glycol) Blends: Mechanical, Thermal And Morphological Properties. Paper presented at the AIP Conference Proceedings. https://doi.org/10.1063/1.4945957
8. Briassoulis, D., Athanasoulia, I. G., & Tserotas, P. (2022). PHB/PLA plasticized by olive oil and carvacrol solvent-cast films with optimised ductility and physical ageing stability. Polymer Degradation and Stability, 200, 1-21. https://10.1016/j.polymdegradstab.2022.109958
9. Caicedo, C., Diaz-Cruz, C. A., Jimenez-Regalado, E. J., & Aguirre-Loredo, R. Y. (2022). Effect of Plasticizer Content on Mechanical and Water Vapor Permeability of Maize Starch/PVOH/Chitosan Composite Films. Materials, 15(4), 1274. https://doi:10.3390/ma15041274
10. Chen, P., Xie, F., Tang, F., & McNally, T. (2021). Influence of plasticiser type and nanoclay on the properties of chitosan-based materials. European Polymer Journal, 144, 110225. https://doi.org/10.1016/j.eurpolymj.2020.110225
11. Ching, L. W., Keesan, F. W. M., & Muhamad, I. I. (2022). Optimization of ZnO/GO nanocomposite-loaded polylactic acid active films using response surface methodology. Journal of King Saud University– Science, 34(3). https://doi.org/10.1016/j.jksus.2022.101835
12. Falqi, F. H., Bin-Dahman, O. A., Hussain, M., & Al-Harthi, M. A. (2018). Preparation of Miscible PVA/PEG Blends and Effect of Graphene Concentration on Thermal, Crystallization, Morphological, and Mechanical Properties of PVA/PEG (10wt%) Blend. International Journal of Polymer Science, 2018. https://doi.org/10.1155/2018/8527693
13. Hanani, Z. A. N., & Husna, A. B. A. (2018). Effect of different types and concentrations of emulsifier on the functional properties of kappa-carrageenan films. International Journal of Biological Macromolecules, 114, 710-716. https://doi:10.1016/j.ijbiomac.2018.03.163
14. Haq, M. A., Jafri, F. A., & Hasnain, A. (2016). Effects of plasticizers on sorption and optical properties of gum cordia based edible film. Journal of Food Science and Technology, 53, 2606-2613. https://doi:10.1007/s13197-016-2227-7
15. Heydari-Majd, M., Ghanbarzadeh, B., Noghabi, M. S., & Abdolshahi, A. (2020). Poly (lactic acid) based bionanocomposites: effects of ZnO nanoparticles and essential oils on physicochemical properties. Polymer Bulletin, 79, 97-119. https://doi.org/10.1007/s00289-020-03490-z
16. Holcapkova, P., Hurajova, A., Kucharczyk, P., Bazant, P., Plachy, T., Miskolczi, N., & Sedlarik, V. (2018). Effect of polyethylene glycol plasticizer on long‐term antibacterial activity and the release profile of bacteriocin nisin from polylactide blends. Polymers for Advanced Technologies, 29(8), 1-11. https://doi.org/10.1002/pat.4336
17. Irwanto, D., Pidhatika, B., Nurhajati, D. W., & Harjanto, S. (2019). Mechanical properties and crystallinity of linier low density polyethylene based biocomposite film. Kulit, Karet, dan Plastik, 35(2), 93-98. https://doi.org/10.20543/mkkp.v35i2.5624
18. Jantrawut, P., Chaiwarit, T., Jantanasakulwong, K., Brachais, C. H., & Chambin, O. (2017). Effect of Plasticizer Type on Tensile Property and In Vitro Indomethacin Release of Thin Films Based on Low-Methoxyl Pectin. Polymers, 9(7), 289. https://doi.org/10.3390/polym9070289
19. Jr, A. E., Gross, I. P., Saatkamp, R. H., Pires, A. T. N., & Parize, A. L. (2020). Evaluation of mechanical, thermal and morphological properties of PLA films plasticized with maleic acid and its propyl ester derivatives. Polymer Testing, 88. https://doi.org/10.1016/j.polymertesting.2020.106552
20. Judawisastra, H., Claudia, Sasmita, F., & Toni Agung, P. (2018). Elastic Modulus Determination of Thermoplastic Polymers with Pulse-Echo Method Ultrasonic Testing. Materials Science and Engineering, 547, 012047. https://doi:10.1088/1757-899X/547/1/012047
21. Khoirunnisa, A. R., Joni, I. M., Panatarani, C., Rochima, E., & Praseptiangga, D. (2018). UV-Screening, Transparency and Water Barrier Properties of Semi Refined Iota Carrageenan Packaging Film Incorporated with ZnO Nanoparticles. Paper presented at the AIP Conference Proceedings. https://doi.org/10.1063/1.5021234
22. Kim, I., Viswanathan, K., Kasi, G., Sadeghi, K., Thanakkasaranee, S., & Seo, J. (2019). Poly (Lactic Acid)/ZnO Bionanocomposite Films with Positively Charged ZnO as Potential Antimicrobial Food Packaging Materials. Polymers, 11(9), 1-17. https://doi.org/10.3390/polym11091427
23. Kojnokova, T., Novy, F., Markovicova, L., & Liptakova, T. (2021). Changes of mechanical properties of protective polyethylene films applied in transport bottles and containers for liquid media after exposure to selected liquid media. Transportation Research Procedia, 55, 731-736. https://doi.org/10.1016/j.trpro.2021.07.041
24. Li, Y., Li, W., Deng, Y., Shao, J., Ma, J., & Kou, H. (2019). Theoretical model for the tensile strength of polymer materials considering the effects of temperature and particle content. Materials Research Express, 6. https://doi.org/10.1088/2053-1591/aae91b
25. Lizundia, E., Ortellado, M. C. P., Guinault, A., Vilas, J. L., & Domenek, S. (2019). Impact of ZnO nanoparticle morphology on relaxation and transport properties of PLA nanocomposites. Polymer Testing, 75, 175-184. https://doi:10.1016/j.polymertesting.2019.02.009
26. Luangtana-Anan, M., Nunthanid, J., & Limmatvapirat, S. (2010). Effect of Molecular Weight and Concentration of Polyethylene Glycol on Physicochemical Properties and Stability of Shellac Film. Journal of Agricultural and Food Chemistry, 58, 12934-12940. https://doi:10.1021/jf1031026
27. Odian, G. (2004). Principles pf polymerization (4 ed.). New York: John Wiley & Sons.
28. Pillai, S. K., Sivakumar, D., Ray, S. S., Obianom, P., Eggers, S., & Mhlabeni, T. (2020). Active nanocomposite films based on low density polyethylene/organically modified layered double hydroxides/thyme oil to retain retail shelf life and quality of Hass avocados. Paper presented at the AIP Conference Proceedings. https://doi.org/10.1063/5.0029459
29. Rahman, M. M., Islam, M. S., & Li, G. S. (2018). Development of PLA/CS/ZnO nanocomposites and optimization its mechanical, thermal and water absorption properties. Polymer Testing, 68, 302-308. https://doi.org/10.1016/j.polymertesting.2018.04.026
30. Ruz-Cruz, M. A., Herrera-Franco, P. J., Flores-Johnson, E. A., Moreno-Chulim, M. V., Galera-Manzano, L. M., & Valadez-Gonzalez, A. (2022). Thermal and mechanical properties of PLA-based multiscale cellulosic biocomposites. Journal of Materials Research and Technology, 18, 485-495. https://doi.org/10.1016/j.jmrt.2022.02.072
31. Salunkhe, S. R. (2018). Study of Contact Angle and Surface Energy of CuS Thin Film. International Research Journal of Engineering and Technology (IRJET), 05(20), 1930-1933.
32. Sangroniz, A., Zhu, J. B., Tang, X., Etxeberria, A., Chen, E. Y. X., & Sardon, H. (2019). Packaging materials with desired mechanical and barrier properties and full chemical recyclability. NATURE COMMUNICATIONS, 10. https://doi.org/10.1038/s41467-019-11525-x
33. Shahid, S., & Gukhool, W. (2020). Experimental Testing and Material Modeling of Anisotropy in Injection Moulded Polymer Materials. (Master ), Blekinge Institute of Technology, Karlskrona, Sweden. https://doi:10.13140/RG.2.2.12587.87846
34. Shankar, S., & Rhim, J. W. (2019). Effect of types of zinc oxide nanoparticles on structural, mechanical and antibacterial properties of poly(lactide)/poly(butylene adipate-coterephthalate) composite films. Food Packaging and Shelf Life, 21. https://doi.org/10.1016/j.fpsl.2019.100327
35. Shankar, S., Wang, L. F., & Rhim, J. W. (2018). Incorporation of zinc oxide nanoparticles improved the mechanical, water vapor barrier, UV-light barrier, and antibacterial properties of PLA-based nanocomposite films. Materials Science & Engineering C, 93, 289-298. https://doi.org/10.1016/j.msec.2018.08.002
36. Sharma, S., Jaiswal, A. K., Duffy, B., & Jaiswal, S. (2020). Ferulic acid incorporated active films based on poly(lactide) /poly(butylene adipate-co-terephthalate) blend for food packaging. Food Packaging and Shelf Life, 24. https://doi.org/10.1016/j.fpsl.2020.100491
37. Sharma, S., Singh, A. A., Majumdar, A., & Butola, B. S. (2019). Tailoring the mechanical and thermal properties of polylactic acid-based bionanocomposite films using halloysite nanotubes and polyethylene glycol by solvent casting process. Journal of Materials Science, 54(12), 8971-8983. https://doi:10.1007/s10853-019-03521-9
38. Sin, L. T., & Tueen, B. S. (2019). Mechanical Properties of Poly(Lactic Acid). In L. T. Sin & B. S. Tueen (Eds.), Polylactic Acid; A Practical Guide for the Processing, Manufacturing, and Applications of PLA (Second Edition ed., pp. 167_202): William Andrew Publishing. https://doi.org/10.1016/B978-0-12-814472-5.00005-4
39. Speight, J. G. (2020). Monomers, polymers, and plastics Handbook of Industrial Hydrocarbon Processes. (pp. 499-537). United States: Gulf Professional Publishing. https://doi.org/10.1016/C2015-0-06314-6
40. Szlachetka, O., Witkowska-Dobrev, J., Baryła, A., & Dohojda, M. (2021). Low-density polyethylene (LDPE) building films – Tensile properties and surface morphology. Journal of Building Engineering, 44, 103386. https://doi.org/10.1016/j.jobe.2021.103386
41. Yu, F., Fei, X., He, Y., & Li, H. (2021). Poly(lactic acid)-based composite film reinforced with acetylated cellulose nanocrystals and ZnO nanoparticles for active food packaging. International Journal of Biological Macromolecules, 186, 770-779. https://doi:10.1016/j.ijbiomac.2021.07.097
42. Yuan, H., Li, T., Wang, Y., Ma, P., Du, M., Liu, T., ..., & Dong, W. (2020). Photoprotective and multifunctional polymer film with excellent near-infrared and UV shielding properties. Composites Communications, 22. https://doi.org/10.1016/j.coco.2020.100443